Search results

  1. A

    Honda BF135hp 2015

    This is exactly what happened on attached image
  2. A

    Honda BF135hp 2015

  3. A

    Honda BF135hp 2015

    .had a full service approx 12 months back but only done several hours use since
  4. A

    Honda BF135hp 2015

    Hi. I had beeen trolling fishing for an hour at low revs...but when i accelerated up to 3800rpm the Honda malfunction alarm went off every 1 to 2 second intervals with reduced power...no juddering or missing..when in neutral the engine ticked over with no issues....I turned engine off and...
  5. A

    Prop Question

    All. thank you for you're input it seems that a 17p is the way forward! can i ask what diameter would you go for?
  6. A

    Prop Question

    My options. im looking at. 14.8 x 19p 3 blade. 15.0 x 17p 3 blade. 15.5 x 17p 3 blade. 14.5 x 17p 4 blade. i believe that the 14.5 x 19p is the same as a 15.5 x 17p?
  7. A

    Prop Question

    I tried a 14.5 x 17 and lost all cruise speed. it went from 25knts to 22knts.....@25knts i was getting 0.7ltrs per mile. @22knts i was getting 0.9ltrs per mile.....i understand that dropping 2 pitches will increase rpm. the diameter of the prop makes a huge difference. i believe approx 400rpm...
  8. A

    Prop Question

    GEAR RATIO 2.14:1
  9. A

    Prop Question

    im all for cruise. i don't want to loose that. if i kept the 19p and reduced diameter how would that work out.
  10. A

    Prop Question

    i would loose cruise speed by going down to a 17p, i would like to try and keep that
  11. A

    Prop Question

    Hi. i have a Honda 135hp forstroke 2015 model. its currently set up with a 3 blade 14.5 x 19p which gives a cruise speed at 25knts at 3900rpm. 'wot' is 5200rpm and 33knts fully loaded. im on the understanding that the rev band for these motors is between 5000 & 6000rpm. ive been told the engine...
  12. A

    manifold pressure sensor

    Hi, Mercury 115hp 2008 efi fourstroke. recently had issues with the Manifold Absolute Pressure Sensor....whilst removing i broke off the nipple that engages with the inlet air manifold (rookie error) which has fallen inside....my question is would i have to get this small piece of plastic out...
  13. A

    crank sensor

    Mercury 2008 efi 100hp four stroke, after a day out fishing my outboard wouldnt start, i removed plug and turned engine over, No Spark, tried again and started on 3 cylinders, replaced spark plug and wouldnt start again, after several attempts it started and ran smoothly, it seems erratic...
  14. A

    Smart Craft Guage question

    Hi, Mercury fourstroke efi 2008 100hp, currently has annalog guages rpm battery trim guage, i wish to fit smart craft monitor to engine, i have seen a yellow plug which says terminator with a smaller plug which looks like a 3 pin plug next to it, question is, if i plug a blue coloured data lead...
  15. A

    Mercury EFI Fourstroke 100hp

    Hi, bit of a strange problem, I have a Mercury EFI 2008 Fourstroke 100hp, Battery fully charged, turns engine and starts with no problem, leaving battery connected over night until next morning and engine barely turns over as if battery is flat but the battery is fine, disconnect battery for a...
  16. A

    Mercury OutBoard Fuel Issues

    Hi all, I have a 2008 Mercury Four Stroke EFI 100hp my problem seems to be the fuel doesnt run smoothly to the injectors, whilst priming VST the fuel pick up pump runs for approx 5 seconds and turns off, engine starts fine and runs on the muffs for 10mins or so before it starts to run lumppy...
  17. A

    Mercury & Smartcraft

    Hi, Re...Mercury four stroke efi 100hp 2008 Im wanting to fit a smartcraft instrument to my outboard, is my outboard to old? Thanks.
  18. A

    Mercury alarm

    Hi all, I'm new here from England. I have a Mercury four stroke efi 100hp 2008 model. On turning the key I get the usual alarm check of 1 beep, on cranking the engine the alarm beeps again until started. Once it's started alarm goes off, Do you no or think their maybe an issue. Thanks Andy
Top