Search results

  1. M

    2005 60hp 4 stroke BF hard to start, runs fine-then hard to start

    2005 bigfoot 60 horse 4 stroke elptoefi. Have to crank multiple times to get started. Once it is started it will run all day. Once turned off it is still difficult to start again. I am thinking fuel pump. Any suggestions or feedback? Thanks.
  2. M

    outboard continues to crank after key is removed

    i have a 2005 mercury 60 hp bigfoot. i went to start it and the motor kept cranking after i took key out. i had to disconnect battery to stop it. now i cant connect battery without it cranking immediately. what is going on? I even put it in gear and it still immediately cranks when i connect...
  3. M

    2005 60HSP EFI 4 stroke Big foot fuel issue

    I purchased this motor last year. Started fine on first try all season (live in midwest). Winterized and Summerized by the book. Ran fine for first few months and then out of the blue it started loosing power after 10 minutes or so of running at full throttle. Problem has worsened to the...
  4. M

    90hsp 3cyl chrysler intermittent spark question

    I have a 90 horse 3 cyl chrysler circa 73-74'.<br /><br />I have tested for spark and it seems that right off the bat the spark is strong for 2-3 seconds and then drops off and becomes erratic. I know it could be about 7 different things but was hoping for suggestions of the most common. cap...
  5. M

    90 horse chrysler fuel issue at start and Idle

    I have a 90hsp chrysler 3 cyl. I think that there are only 2 models with that hsp. I am thinking that it is a 73 or 74.<br /><br />When starting it seems that way too much fuel is being dumped into the carbs. If it does not start right away, it will flood. Also, once started, it seems that...
  6. M

    Piston identification

    I have a 90hsp 92 Mariner outboard 3 cyl.<br /><br />I was trying to figure out exactly what pistons I have in it. I have the crankshaft removed and the only info on the pistons read "B 3133" and then "52 C" right below. It reads the same across all 3. Just curious if I was looking in the...
  7. M

    Flywheel Puller for 92' 90hsp mariner

    Is it true that I should not use any other flywheel puller than the one mercury sells for $80.00 with the threads on the outside? Some people have told me that using a 3 bolt puller would work also. I would appreciate some opinions.<br /><br />Thanks
  8. M

    hole in the side of piston?

    I have a 90hsp 1992 Mariner 3cyl 2stk.<br /><br />I recently took apart to see why it ran so bad last year and found a hole in the side of one of the pistons. I assumed that the rings may have been bad but was surprised to see a hole in the side. I need help with a few things.<br /><br />1...
  9. M

    92' 90hsp mariner electrical issue

    This is my last chance before starting the bad road of buying parts. I have an intermittant spark problem. I ran tests according to my tech manual and here are the results:<br /><br />Charge coil: <br /><br />Blue stator wire to Red stator wire I received no reading.<br /><br />Red stator wire...
  10. M

    Please help me interpret stator test results

    1992 90hsp Mariner<br /><br /><br />I just finished the recommended stator resistance tests from my tech manual. The blue and red wires on the switchbox from the stator were tested. I got a perfect reading from the red wire to ground test. However, I got no reading at all from the red and...
  11. M

    Starting from Selenoid

    Can I crank my motor (90hsp 92')from the selenoid so that I can run some tests? If not, is there a better way to accomplish the same thing?<br /><br />Thanks!
  12. M

    Mysterious spark issue

    1992 90hsp mariner outboard 3 cylinder 2 stroke<br /><br />I have been experiencing some odd issues with this motor. I live on a lake and have been using this motor all summer. My problem has only occurred one time prior to this time. I will try to keep it short and to the point.<br />1...
  13. M

    92' (2 stroke) 90 horse mariner

    My motor is running rough at idle. Also, at full throttle, runs smooth but only at 3200 rpms. Last year ran smooth all the time and ran at about 5200 rpms. Obviously, I'm running at about 60% power and I think I need to adjust the carbs. Any advice on where to start? I bought a used service...
Top