The iboats forum moderators are excited to announce that at this time it appears the iboats forums posting pictures function is working once again. Though we cannot promise for how long, we're hoping for indefinitely.
1987 evinrude keeps puttering and cutting off. There is light blue white cream on the bottom carb and a little on 2 more carbs when it's running. The bottom carb seems like its spitting out fuel or maybe water from the throttle part. I checked the reeve valves and the look good. Could it be...
1987 140hp evinrude ran good yesterday. If your standing in the back of the motor the right side was getting hot because it wasn't pumping enough water to come out of per hole. Today I went to choke it and fuel came out the red enrichner knob,it had a crack in the knob. I took the fuel inrichner...
1973 4hp evinrude not get fuel to choke it. Carbs are cleaned,fuel is filling up the carb bowl ,needle and seat is in perfect condition,float is level and floating like its suppose to. In having problem with it staying running. The long idle screw at the top of the carb I don't know how many...
2007 60hp Johnson not getting fuel I think. When it runs it just quit on me. You poor gas in it u don't mix it. I don't know if its gumed up or not. It's on a plantain boat. Any help would be very appreciated. Thanks
I have a 1999 40hp Johnson tilt n trim leaking oil from the metal thing that pushes the motor up and down. I guess the black rubber around it is bad. What's the flat rate time in repairing that or the price they would normally charge to repair it. Thanks
1982 115 inline 6 mercury has 3 fuel enrichners on the side of each carb. The main one in the middle with 2 electric wires coming from it is getting fuel in the line. Fuel is not going to the other fuel enrichners. The lines are clear so u can c right through them. Why aren't the other 2 getting...
1982 115 inline 6. Electric fuel sender is working. The problem I have is fuel is coming from the fuel sender line to the thingy on the side of the carb. The other 2 carbs have that same small line on them and they are clear so u can c through it but know fuel is coming through those lines. The...
How do u set the throttle cable for 1980 115hp Johnson or for all Johnson n evinrude beginning from 1977 to 1990. Is it a certain amount of turns. I have no problem setting the shift cable at all it's just the throttle part I'm having trouble with. When ever I set the idle it's perfect and when...
1965 Johnson seahorse electric gearshift not shifting. Where do they come from and how does it work. The wires are blue and green. It just all of a sudden stopped working
How can I find out if the vro pump is pumping oil to the carbs. Could I just look into the carb bowls and c if the gas is mixed or not. It's a 1986 70hp evinrude 3cyl. Thanks
On port side of engine it's 95 97 94
On port side it's 110 111 115. Will that make any difference on the engine if one side has higher compression than the other. It's a 1979 evinrude with a 1988 engine. Thanks. Runs good though😁
1980 115hp evinrude tilt n trim keeps easing down by itself. I've tighten the release valve on the side of the tilt n trim and its still doing the something. There are no leaks anywhere. I haven't tried filling it up with oil yet though.
Line from carb going to port side if engine smoking a little and a little gas is up under it on engine. What should I do to fix the problem. I don't want the engine to blow up on me. Thats
Everything is brand new on motor. Carbs cleaned,new fuel pump and lines,perfect spark,new gas tank,fuel getting to all carbs,new primer bulb,compression is 120psi down the middle. Motor won't get on plain unless u go to the back and hit the throttle about 5 times then it gets on plain. When it...
1985 70hp not getting enough fuel to run full speed. There are no air leaks,120 compression in each cylinder,good spark,new fuel lines,carbs cleaned 3 times,carbs are tight against the block and gaskets are good. Needles not sticking,gas is going to every carb through hoses. Please help. It runs...
