Search results

  1. R

    stator wiring

    i have a 88 johnson gt150 and i was wondering if it matters if you reversed the wires on the stator will that make any difference. I bought a cdi stator and it doesn't have the gray stripe on the one wire, but i matched the harness lengths up so i assume its right. Thanks
  2. R

    Tach reading only half RPMs on johnson GT150

    Well guys i haven't posted in a while ( which is good ), but i ran into a tach problem. The volts were reading 12-13 at wide open and the tach is dead, so i replaced the voltage reg. that fixed the charging issue but now the tach reads 2800 rpm when i know its around 5500. I have replaced power...
  3. R

    smart tab install

    Guys, i have an ebbtide dynatrack fish n ski, i bought a set of mobster tabs for angled transom. My question is the transom is not flat, there is a little curve to it, about 1/8 inch over 8 inches, can i just stack stainless washers for the few holes. Thanks for input
  4. R

    smart tabs for a fish n ski

    I was wondering if anyone has tried these for this type of boat. The reason i ask is i get some hopping or porpoising when cornering with it trimmed in. The other problem i have is a swim ladder on the back, and wondering how they fit when the ladder is down to get back in the boat.thanks for...
  5. R

    smart tabs for a fish n ski

    I was wondering if anyone has tried these for this type of boat. The reason i ask is i get some hopping or porpoising when cornering with it trimmed in. The other problem i have is a swim ladder on the back, and wondering how they fit when the ladder is down to get back in the boat.thanks for...
  6. R

    sanding paint off lower unit

    I was wondering if it matters that there is paint on the lower unit because mine was peeling bad and i decided to take it off. Would this corrode or act as a sacraficial anode any input is appreciated. BTW it's in freshwater. Thanks
  7. R

    stiletto prop question

    i don't know if any of you prop gurus know if adding cup to a stiletto 21 pitch prop would make a difference in prop efficiency when mounted high on the transom. I have a johnson 150 on a fish and ski thats mounted to the transom in the 3rd out of 4 holes from the top, my rpms are good but i...
  8. R

    71 johnson 9.5 high speed adjustment

    i was wondering if there is a high speed adjustment on the carb. The motor runs great in the spring and fall but in the summer or warmer weather its a dog.
  9. R

    prop for 150 gt

    i have an 1983 ebbtide dynatrak 17'6" with a 1988 johnson gt150. The boat weighs about 1600 pounds loaded and i have a 21 pitch stiletto without a jackplate. The motor is in the middle hole which is about 1 inch above bottom of boat. my rpm's are 5600 and running 51 mph on gps. I'm wondering if...
  10. R

    waxing bottom of boat

    i was wondering what you can use on the bottom of the boat to wax it or make it faster. I used scotchbrite brillo pads to clean it and scuff it lightly, but i don't know if thats the best idea.
  11. R

    WHAT SIZE TROLLING MOTOR

    i was wondering what size trolling i would need for a 17.5 foot ebbtide dynatrak fish and ski, it weighs about 1800 fully loaded, thanks for any help
  12. R

    is 92 octane non- oxygenated gas o.k to use

    i have a johnson 150 that was rebuilt a year ago and i've been runnin 92 non-oxygenated gas and amsoil synthetic ,i was wondering if this is a waste of money, my carbs don't get gummed up at all
  13. R

    anybody know weight of ebbtide dynatrack

    I have an 83 ebbtide dynatrack 176sk, i was wondering if anybody knew what the boat weighs and how well built they are. It only goes on gps 47.4 mph with 19"pitch aluminum and 150 johnson and about even with the bottom of boat
Top