Search results

  1. H

    9,5 exhaust problem

    hi there! have 3 9,5hp engines, every one with problems. This one had a exhaustleak in the tower so I had to use it without cowl. Made a plug with silicon. The engine runs, doesnt leak, but when I try it in the water it wont start, even if it runned 5 sec ago! Big problem?
  2. H

    9,5 carb problems

    Hi! one of my 9,5 wont run without choke, belived this vas a carbproblem, but carb and low-speed needle works great on other motor ( runs a bit bad on lower rpm). Switched carbs between both, switched floats. Once I got it running, but the carb sparyed out fuel on top ( some kind of...
  3. H

    unknown carbs

    Hi! offered 5 carbs, Partsnr. on 2 fits to my 25hp, so what is the rest?<br /><br />1. 321406<br />2. 315082<br />3. 322299<br /><br /><br />dont know what brand they are......
  4. H

    john 25hp 1972 paint/carb

    Hi, got a 25hp johnson as a parts engine for my 1970 20hp. Outside it has the standard green, but inside the paint is dark green (standard 1969-1971) on the halve side with carb/reed, and the side with cylinder it has same color as the outside. Is that standard? ( look at this ad, it has the...
  5. H

    Wont run without choke

    My 88evinrude xp10 has a bit carb.problems, it wont run without choke, hard to start, HELPHELPHELP<br /><br />sparkplugs; champion l77jc4 or something like that.
  6. H

    how old is this motor

    I have been offered a Evinrude XP10, that is black. Looks exactly like a 9,9 or 15hp engine from 1974+ . About how old is it?
  7. H

    change thermostat on 9.5hp

    I took off the three screws,and the head is sitting like h***<br /><br />how should I get it off?
  8. H

    get lower unit off

    broke three screws off, how should I get it off? it is a 9.5hp
  9. H

    runs poor on idle.....

    my 9.5hp runs poor at idle, it has a good high rpm, but it barks a couple of times and stops. checked carb and it is clean, could it be the low-speed-adjustment knob?
  10. H

    low water pumping

    Shanged impeller and thermostat om my 10hp, but it pumps weak, bad gasket? (using silicongasket)
  11. H

    will this impeller pump water?

    The impeller on my 18hp Johnson has a bit of the impellerbalde broke off (the big en on one of the blades)<br />My dealer cant get me this part before 1.may,and I need the impeller tomorrow.
  12. H

    cylinderhead gasket on 10hp

    need a cylinderhead gasket on my 1960 10hp johnson. The shop can get a headgasket to a 10 hp 1961. Does it fit?
  13. H

    johnson 10hp impeller on 18hp?

    i have one spare impeller to my 10 hp 1960. Have an 18 hp 1963 without impeller, they look the same, so, can I use the impeller?
  14. H

    lower unit on Johnson9,5 1973

    the oil-seal began to leak, so i wanted to take off the lower unit to look at it. It is a salt-water engine. The first screw,okay, then, the other tree broke off. Well,as long as i get the lower unit off it is okay, but it will not move an inch. tryed with a hammer at the cavitasion-plate...
  15. H

    cylinder top torque 9 1/2 and 18hp

    Have an Clymer-manual that says 96-120 in.-lb. at cylinder head bolts. my tool has scale for ft.-lb and kgm. How many ft.-lb are 96-120 in.-lb?
  16. H

    important notice at the top of this page

    "Important Notice: Many forum members have asked for the following services...so we are proud to announce that iboats has created Boating Thrifties and Boating Want Ads areas for our Forum members!!! To kick these new areas off, placing ads will be FREE to all Forum members until Feb 15...
  17. H

    Gear troubles on 10hp

    Tuned up my 10hp Johnson 1960. Removed the skeg and ut it bak together. I tryed it last night and the gear troubled. First I sat it in reverse, and nothing happened ( I tought it was the shift rod connector. It worked fine in Forward. I pulled it bak to neutral and it didnt shift. I pulled it...
  18. H

    paint for a 1963 johnson

    I need some paint to my 18hp Johnson 1963, it is a kind of grey-white. Is it a paint-code/paint-name for that specific paint?<br /><br />Look at "readers gallery" at http://mitglied.lycos.de/old_omc/ there you can see pics of it. Thanks for any answers, the paint is so expencive that i would...
  19. H

    replacing impeller, 10hp 1960

    I took out the old impeller and did see that the blades was bended, and I did not remember wat way it went ( it goes with the clock, but sould the blade bend with??)
  20. H

    spark-plugs

    I need spark-plugs for my engines, i use NGK,what is the right type/heat?<br /><br />1. Johnson 10hp 1960<br />2. Johnson 18hp 1963<br />3. Johnson 9,5hp 1973<br />4. Johnson 20hp 1970
Top