Search results

  1. B

    slow switch will it kick in

    1989 60 hp evinrude heat alarm comes on changed everything put alarm sensor.if i unhook the alarm sensor the one tan wire and run the engine and it gets over heated will the SLOW switch kick still take it down to 200rpm or are the sensor and SLOW switch connected
  2. B

    60 hp overheat alarm,frustrated

    1989 evinrude get over heat alarm after 5 minutes replace water pump,replaced vernatherm or Tstat,change prop to get 5000 rpm at WTO,.cleaned carbs,decarboned cleaner,changed plugs,took T- stat out,RUNS COLD,wont idle well,unhooked heat alarm but heads felt hot,pee water was just mild...
  3. B

    89 evinrude 60hp rough idle/slower top end

    over heat alarm came on 2 times put new water pump in. the old one was still good,took out thermostat for now til get new solved overheat i think ,but wont idle very well.130 compression ea. cylinder ,plugs are wet,sprayed stater fluid on outside motor to check for leaks no high idle from that...
  4. B

    what is a rectifier

    what does it do
  5. B

    60 evinrude tech tip ??

    just found out from my tec about 89-96 motor have cooling hose coming from bottom exhaust side cause overheating.tech update say to drill new hole 2'' down and 1 3/8 across and drill 11/32 hole NO MORE THAN 1/2'' DEEP and tap1/8 pipe thread and install elbow at top. brass plug bottom can anybody...
  6. B

    60 hp evinrude

    how hard is it to install water pump on 1989 60 hp
  7. B

    89 evinrude water pump

    60 hp needs water pump ,very mechancal minded person doing for the 1st time,how do remove pin or bolt in shift link under carb, then unbolt lower unit any secrets or thing should know
  8. B

    how to check timing 60 einrude

    i have a little rattle in my motor keep double oil in gas /vro 2 compression is 130# each cylinder need to check timing how? :confused: :confused: or could i ck something else ,maybe take off to head check cylinder,got a over heat alarm let cool for 10 min started get a rattle
  9. B

    1989 evinrude powerhaed decision

    i can get a power head ready to go for $1100. or get my powerhead rebuilt still holding 130# percylinder
  10. B

    1989 evirude 60

    my engine has a little rattle the cylider compression is 130 per cylider i run 10 oz of oil in 5 gallons of gas with the vro 2
  11. B

    evinrude decals or cover refurb.

    where can i find a 1989 60 hp evinrude or refurb
  12. B

    1989 evinrude 60

    where can i find new decals or someone to refurb, my top motor cover
  13. B

    1990 40hp evinrude

    i,am wanting to replace the power head what kind of connection am i going to run in on bottom? if you can help talk me thru replacement? got rebuilt powerhead for 900.00$ is that good ,w/15mos. warrantee :confused: javascript:void(0)<br />Confused
  14. B

    1990 40 hp evinrude vro tell me if i fried it

    have a tick sound in top cylinder run good but i dont know if vro was working correctly, what does sound like when fried ? spark plugs light brown and wet on bottom/top dark brown not as wet. Put new spark lever cam on it broke, could the spark control rod out of adjustment cause this? using vro...
  15. B

    1990 evinrude 40 hp vro

    i am getting a tick sound in top end of top cylinder i have no alarms,but i did have spark lever cam break and i replaced it,do you think the spark control rod could cause this? or vro system falure on top piston
Top