Search results

  1. B

    Johnson 1977 115 hp no spark 1 and 3 cylinder

    No spark on 1 and 3, good spark on 2 and 4. Changed all plugs, changed 1 and 3 coils, changed power pack, changed timer base and sensors, did not change stator. Tried to start again with same results, no spark on 1 and 3. Does anybody have any ideas on what my problem may be? Thank you.
  2. B

    2 1971 OMC 125 HP outboards, Different pulse packs and plug ins

    Johnson 125ESL71C and Evinrude 125183C. Both motors call for 0384522 pulse pack. Johnson has the right 5 prong plug, for wabash pack, Evinrude has a 3 prong plug for a prestolite, how can I use the 0384522 5 prong on the Evinrude. Thanks for any help.
  3. B

    1972 chrysler 55 hp no power to points

    In the wire connecting block I Have power in the red terminal and the 2 point wires are connected to white and blue terminals and no power at the points with ignition on. Could anybody tell me if 2 wires leading to points are in wrong position? 1972 555HD
  4. B

    1971 johnson 125 water shooting out of hole in front of lower unit

    Had it running in a tank and as water got lower I noticed water shooting out of a small hole where lower unit meets exhaust housing in front of lower unit. Is this normal?
  5. B

    no needle valve bearings on 1971 125 johnson

    Doing a carb rebuild on a 1971 125 johnson. When i removed the needle valves I noticed there were no plastic needle valve bearings at the tip of the needle valves. Is it possible they are still stuck in the seating area of the carb or is it possible that they were not used . carb schematic only...
  6. B

    Lots of sand 1988-88 spl

    Bought a 1988 88 spl knowing the last time out the hot horn was on. Removed lower unit, about a cup of sand spread around, and also sand in impeller housing, Removed thermo housing and also packed with sand. Is it time to pull the heads and check or should air gun and hose complete the sand...
  7. B

    compatible coils johnson 115

    Could anyone tell me if coil number 581032 from a 1973 115 johnson can be used on a 1977 johnson 115 which calls for number 581610?
  8. B

    seal between motor and exhaust housing 1977 25 hp johnson

    Could anybody tell me about the sealing material between motor and exhaust housing on 77-25 johnson. Thought is was a blown out base gasket but after dissassembly found it to be a sealing material not listed on schematic directly outside of the base gasket. Can it be eliminated?
  9. B

    acceptable compression on 1989 evinrude 88 spcl.

    Is 110 per cylinder enough compression for a 1989 88 spcl to run well?
  10. B

    Color of 1974 Johnson 85 HP outboard

    Does anybody know the paint color of a 1974 johnson 85 HP outboard? Looks like a goldish green, more goldish on the powerhead.
  11. B

    1974 85 hp johnson and 1975 70 johnson coil interchange

    have a 1974 85 hp v4 parts motor with new coils and a 1975 70 hp 3 cyl with cracked coils, except for the longer spark plug wire they seem identical, they mount up fine, does anybody know if they have the same output and would be ok to use?
  12. B

    function of thermo switch on 1971 johnson 125 hp?

    What is the function of the thermo switch # 383519 on 1971 johnson 125 hp outboard?
  13. B

    1983 merc 25 hp electric, Jet Drag screw question, BC1C carb

    Purchased this project motor and jet drag screw is apparently missing as there is an empty hole with threads directly across from idle screw hole. Three screws are listed for BC1C carb, .088- .090- .092, Does anybody have any knowledge of which to use and what is the function of this screw...
  14. B

    1983 merc 25 hp electric, black wire in harness question

    Acquired an 83 25 hp remote control motor with a 6 wire harness # 6249174. Some of the wires were disconnected, and I'm not sure where the black wire connects and does it relate to the on-off switch? Thought it connected to the lower small solenoid connection, but it will not crank without an...
  15. B

    johnson 125 1971 port to starboard temp

    Is it common for a 1971- 125 to run hotter to touch on the starboard side? Seems to be the same with or without thermostat. Or may i be looking at some blockage? Thanks for any help.
  16. B

    1971 Johnson 125 electric shift no neutral after rebuild

    Dissasembled gearcase, new pump, new clutch dog, new seals, checked solenoids- 5.5 ohms, plunger slightly below top of solenoid, proper voltage to solenoid leads, N-power green, D- no power, R- power green and blue, new type C oil, still can't find neutral, have only tested on a hose. If reverse...
  17. B

    1971 johnson 125 hp electric shift not cooperating

    Gearcase has been rebuilt, new pump, seal, band, shift dog, seals, fluid, old solenoids 5.5 ohms, reassembled, put motor in tank, ran for about a minute, put in forward, motor stopped like key was turned off. Same from neutral to reverse. Bought a nice shifter that tested good, no power to green...
  18. B

    Clutch dog direction, 1971 johnson 125

    Reassembling gearcase, new oil pump, seal, seal band and now clutch dog. Original was well worn so I replaced it. Manual says Three ramp side must face forward end of gearcase. Both sides of new and old clutch dog have three ramps, the only difference is the new dog has an extra drop about 1/4...
  19. B

    Oil in shift solenoid housing 1971 johnson 125

    When motor is operating properly and fluid levels are correct, should there be oil in the shift solenoid housing in the gearcase.1971 125 j0hnson hydro-electric shift.
  20. B

    1971 125 Shift solenoid plunger to oil pump

    Preparing to replace oil pump, Unit drained, looking down the solenoid chamber and a rubber seal looks dangerously close to the small hole for the shift plunger rod, as if it might interfere with proper connection. Could anybody tell me if this is normal or if it could a problem. I assume it is...
Top