Search results

  1. Justinde

    Thank you all who contributed

    She’s up and running…. 1988/125. New head gasket, thermostat,water pump, engine mount. Timing done. Purrs like a kitten.
  2. Justinde

    Can I use any 2 stroke oil?

    Thank you brains trust…. I’ll go buy some marine 2 stroke…. Oils ain’t oils 🙂
  3. Justinde

    Can I use any 2 stroke oil?

    Can I use any 2 stroke oil ( mower etc) or does it NEED to be “ marine” oil?
  4. Justinde

    Bad trigger? Can’t adjust timing

    Not 💯 sure but timing should be 32-34 BTC…..
  5. Justinde

    1988/125

    Thank you kindly….. I’m happy to run her at 3/4 throttle and around 35M.P.H as opposed to full throttle and 45 M.P.H….. The fish will still be there 🙂 Fuel burn was pretty good. I used about 15 liters for a realistic 2 hours run time, including trolling and low speed “ get her on the wharf”...
  6. Justinde

    1988/125

    Hi Guys, Replaced thermostat/water pump/head gasket/ lower engine mount…. Running like it should mostly….. I’m running it a little rich, has 145 compression on all 4, but should I run it rich and 3/4 throttle, or nail it to 💯 throttle?? Video of her running in a bucket.
  7. Justinde

    Lower Engine Mount/Shock advice

    Thanks Jerry…. Another difference was that one is $45.00(US) used, and the other ( EBay Chrysler part) is $20.00 OEM new…. I’ll buy the eBay item thank you ! 🙂
  8. Justinde

    Lower Engine Mount/Shock advice

    Hi All, question for the brains trust. I have a 1988 year model 125HP, serial 1258F8C, and need a new lower shock/mount. I found the following on eBay MP5953 OEM RUBBER SHOCK MOUNT CHRYSLER FORCE 85346 *NEW OLD STOCK* Now, the serial number for the part is slightly different to what I found...
  9. Justinde

    Timing Question

    Hi Brains Trust, The below was posted elsewhere, and claims Frank Acampora’s incorrect with his tutorial video on timing and carb sync. I used the video and his sticky, and it works a treat, but someone thinks it’s wrong. Any advice would be appreciated. ———————————————————-...
  10. Justinde

    Not permitted

    Not permitted
  11. Justinde

    Opinions please.... 😊

    Hi All, I am going to retire my 1988 Force 125h.p, and a new Evinrude E-tec 115 h.o g2 was recommended for my set up. I understand it's a new engine, but does anyone have any feedback or known problems with this engine? I'm going for power steering as an option, otherwise it will be stock...
  12. Justinde

    125 H.P. (1258F8C) 1988 overheating

    Hi Guys, I just replaced ( last week) my water pump. I have a tell tale, and the water is pumping hard. I have also replaced the exhaust plate, and associated gaskets, as there was a build up of sludge in the water jackets. The engine ( power head) had a complete rebuild ( other than the...
  13. Justinde

    Force 125 Impeller/OEM Question

    Hi All, I recently purchased, and received the impeller in the below link. It has a 5 year warranty ( for a part I replace every year), but my question is this. My original part has a brass insert, this one is hard plastic. Has anyone used one before and not had a problem? Is there any...
  14. Justinde

    1988 Force 125 Overheating

    Hi All, I return seeking some wisdom. Since I bought my boat, I have replaced the exhaust cover and gaskets, as the previous one was full of very old sand ( hardened like concrete). The boat has a new water pump and impeller, timing is correct, and link and sync is done. I went out on the...
  15. Justinde

    1988 Force 125 Engine Mounts

    Hi All, My LOWER engine mount is stuffed. I have previously bought 2 new re manufactured upper mounts, not yet fitted, but it seems the lower one is stuffed. Do I spend $50.00 on an old Chrysler mount, or $200.00 on an OEM re manufactured unit? Installation tips PLEASE. If I am going to do...
  16. Justinde

    1988/125 Engine Mounts and steering

    HI All I have been very quiet the last few years- all is well with the beast. I have a confession, I did get an old school mechanic to check my girl over- not that I don't trust the forum- I just do not trust myself, and for a few hundred bucks, I have peace of mind. Let's face it, unless you...
  17. Justinde

    1988 Force 125 Forward Control Cable Adjustment

    HI All ( again) My 1988 125 has a coupe of issues which I am fairly certain caused by an incorrect adjustment on the forward controls. There are a couple of issues, so I'll list them so as to paint a better picture and hopefully get a resolution to my problem. * Idle speed screw on tower at...
  18. Justinde

    New Impeller

    Hi All Just wondering if someone can cast their eyes over this and tell me if it is the right part for a 1988/125 Force?? I have replaced the waterpump in the past but I want to make sure before I buy it!! http://www.justboating.com.au/Water-Pump-Impeller---Sierra-S18-3030.html#producttabs
  19. Justinde

    Battery/Tilt Trim

    HI All Took the boat out this week after fitting a tell tale. Its been a while since it ran, so did the timing/link sync etc, new fuel. I had a couple of questions and don't mean to make a 2 pronged attack!! by the way its a 1988/125 Question 1: The boat started just fine, cranked well...
  20. Justinde

    Chrysler L drive

    Hi All I was driving my kids to soccer yesterday and noticed an older boat on the side of the road. It had an L drive ( mercruiser) set up, but the leg was all white and it had the 'cone' on the end of the prop, which makes me ask, per the topic of the thread, did Chrysler ever make an L...
Top