Search results

  1. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Where do I disconnect the trim wires to feed them through the rubber grommet?
  2. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

    I am tryin to hook up the Airmar External Transom Temperature Sensor T80 10k ohm Analog Thermister as a fix but do not know how to wire it. There are 3 wires on the temp sensor. They are blue, black, and metallic. What wires on the unit do you connect these to? A wiring diagram will be very...
  3. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Will my current manifolds be able to swap to the new Vortec heads? Will my Mercarb 2 bbl work on the Vortec heads too?
  4. N

    Where to get 1992 Mercruiser 4.3 solenoid plastic cover?

    Does anybody know where I can get the plastic part that covers the solenoid wirings mounted on the starboard side manifold?
  5. N

    1992 Mercruiser 4.3 Alpha One Gen II has water in oil after rebuild.

    The boat is 1992 Bayliner Classic 2252 that has 1992 Mercruiser 4.3 with 1 piece rear main seal. I got water in oil after rebuild. Changed oil 4 times and still has water. Motor was frozen when I got the boat. Tore down the motor and there was water in cylinder #4 & #6. Had a machine shop...
  6. N

    1992 Mercruiser 4.3L 262 CID Pre-Vortex Back Fires

    1992 Bayliner 2252 w/ 1992 Mercrusier 4.3L keeps on backfiring. Just rebuilt the motor. Could be valve adjustment too tight or timing is off? Please assist w/ troubleshooting.
  7. N

    Can't find 1992 Mercruiser 4.3 Pre-Vortex intake manifold

    Has 12 bolts. Can't find replacement. Any suggestions?
  8. N

    1992 Mercruiser 4.3 Alpha 1 Gen 2 cam shaft plug install

    I rebuilt the motor, installed it back on the boat but forgot to put in the cam shaft plug back in. Found out while braking in the motor and noticed a leak by the flywheel. Motor runs awesome! I was wondering is there an easier way to install the plug without completely raising the motor from...
  9. N

    1992 Mercruiser 4.3 Alpha 1 Gen 2 Motor Knocking Noise

    Bayliner 2252 Classic has been sitting since 1992 and the motor was frozen / stuck when I bought it. Got it to run and took it out. When at 3500 RPM the motor made a knocking noise, smoked, overheated, and shut off. Wouldn't start again until motor cooled. The knocking sounded like it's...
  10. N

    Mercruiser Trim will not trim all the way up.

    1992 Bayliner 2250 W/ Mercruisr 4.3 and Alpha One Gen II drive. The trim motor is: TRIM MOTOR MERCURY 14336A15 14336A20 14336A6 with BRACKET Trim down works but trim up only goes half way up. Please advise how to troubleshoot. Thank you.
  11. N

    wiring

    What happens if you hook both wires red/yellow and purple together on the terminal closest to the block? Will it damage anything?
  12. N

    Mercruiser 4.3 will not start after using diesel to free stuck motor.

    Got a Bayliner 2552 w/ a Mercruiser 4.3 V6. It had been sitting for 25 yrs and the motor was frozen/seized. I poured diesel to free up the motor. The motor was freed up but will not start. It does turn over. I sprayed ether and it helped but will not combust. Got new battery, starter and...
  13. N

    Engine circulating pump

    Does the engine circulating pump affects water intake when engine is ran w/ muffs? I have redone the impeller many times but still not getting water pick up. I have a Mercruiser 888 w/ Pre Alpha drive.
  14. N

    Mercruiser 888 Lower Unit Replacement MC-1 Pre Alpha 1.47 / 1.5 gear ratio

    I am trying to replace my lower unit per it was stolen when i was servicing it. Does the gear ratio 1.47 / 1.5 affect what unit I buy or can I just by one that fits? Thanks!
  15. N

    Mercruiser 888 impeller lower hose is not picking up water after impeller replacement

    I'd just replaced the impeller for a 1977 Mercruiser 888 and the lower hose is not picking up water. I connected a garden hose to the engine circulating pump and ran the motor. Water does come out of the outdrive water discharge when connected to the garden hose. Could it be the engine...
  16. N

    How to remove MerCruiser Alpha One Gen I drive gear from upper drive shaft?

    How to remove MerCruiser Alpha One Gen I drive gear from upper drive shaft?
  17. N

    Mercruiser 3.0 (140hp) Apha 1 Drive control & throttle cable adjustment.

    My prop will not engage when shifted to Reverse. There is no movement on the lower shift cable when I put the control in the Reverse position. However, I was able to shift by just pulling on the lower shift cables manually. The lower shift cable has been replaced a couple days ago by a local...
  18. N

    Rochester 2 barrel carburetor dies after running for 20 minutes

    Rochester 2 barrel carburetor dies every time after running at high rpm. It idles on land and at the dock perfectly but after running at high rpm for 20 minutes in the ocean it dies and will not start back up. I have to wait for about half an hour before it will start again. I have already...
  19. N

    2001 Yamaha 4HP outboard F4MSH propeller size or part number?

    What is the part number for the propellor for a 2001 Yamaha 4hp 4 strokes outboard? Don't know what propeller to buy for my 2001 Yamaha 4hp 4 strokes outboard.
  20. N

    Mercruiser Pre Alpha trim senders wiring schematic

    I am rebuilding my trim senders limit and position. I do not know where to hook up the wires once you pull them through the transom. I have the manual but it doesn't say anything about the wiring. Please advise.
Top