Search results

  1. P

    Trolling motor cable on my 373V broke

    My Motorguide Tour Edition 80lbs trolling motor steering cable broke and I'm not sure what the the length should be on a replacement. Anyone have an answer? I have read that the most common length is 63". Any truth to this? I left this message in the trolling motor section but have not gotten...
  2. P

    Motorguide steering cable broke

    I have a Motorguide Tour Edition 80 lbs thrust trolling motor and my steering cable broke. Does anyone know what length cable will fit this motor? Someone said 63 inches is the most common length. Are they right?
  3. P

    1987 Pro V 150 trim problems, still

    My trim and tilt will work for about ten seconds and then quits. After a few hours it will again run for about ten seconds and quit. I replaced the relay switch but the problem persists. I filled the trim fluid to full so that's not the problem. Could it be I need a new motor? I'm supposed to go...
  4. P

    Gear lube question

    I have a 1987 Pro V 150 and I purchased a quart of Yamalube Marine Gearcase Lube HD but when I went to replace my old lube I noticed it was a lot thinner then the old lube is. This was recommended by local marina. I am wondering if the new lube is right for my motor as it is so much thinner...
  5. P

    1987 Pro V 150 trim relay

    What is the model number for thetrim relay control on the 1987 Pro V 150? I think it starts with 6G5- something.
  6. P

    1986 & 1987 Pro V 150

    Are the 1986 &1987 Pro V 150 motors the exact same?
  7. P

    Yamaha Trim and Tilt Gauge

    Hi everyone, my 1987 Yamaha Pro V 150 trim gauge does not work. I want to get it working again so does anyone have an idea where I should start looking to find the problem? The trim and tilt works just fine on the motor so that's not a problem.
  8. P

    Non working trim gauge

    My 1987 ranger 373v has a trim and tilt gauge that doesn't work any thoughts on where I should start looking for the problem at?
  9. P

    In floor trolling motor control

    I have an 1987 373v and am wondering if I can and how easy it would be to put my tolling motor control into the floor. Any Ideas?
  10. P

    Water pumping question

    My son owns a mid 70's 500 but couldn't get the stream of water to come out of the water port so he blew the tube out with compressed air and now the water comes out of the gasket area instead of the port and the motor ran for 20 mins and never got hot. My question is, will this cause lower unit...
  11. P

    Replacing spark plug wires on 1953 evinrude 15 horse

    I need help getting my second spark plug wire off. I got the first one off with a ratchet and a 1/4" socket with a screwdriver bit in it but I can't get a good enough grip on the other plugs screw to get it out. Any tricks that you folks might know of so I can get the wire replaced and finish up...
  12. P

    Pressure Tank Question

    I have an old pressure tank that I bought a few weeks ago. I was wondering if there is supposed to be some kind of gasket for the fill cap to set against when its screwed down all the way? It looks like it should have something there but I'm not sure. Any help would be great. Thanks, penning7
  13. P

    Lower unit lube in a 53 fastwin?

    The lube in my 53 lower unit appears to be quite thick. Is it supposed to be that way or has it been sitting to long? It's been in my basement for 25 years and evrything still moves. Also any ideas on how to get a frozen lower unit vent screw out?
  14. P

    Lower unit on a 54 Evinrude

    What kind of lower gear lube should I use on my 1954-15 horse Evinrude. The repair manual says type C lube, but I also read its not made anymore. Any alternatives? The lube in my lower unit seems very thick is that normal or is it this way because it's been sitting for over 25 years. Any ideas...
  15. P

    Cover over the coils and points

    I have never worked on a boat motor before and have very little knowledge of doing so except for what I read here and common sense things. I want to replace the coils on my 1954 Evinrude 15 HP motor but can't seem to get the cover off to get to them. Is there a trick or a special tool I need to...
Top