Search results

  1. B

    fuel pump

    After reading manual I suspect a pin hole in the fuel pump diafram. My question is, will I end up with little parts falling out to take it apart and put in a new one??? Hope it is a simple task as it looks in the book. Thanks for any help o n this......Bsandy.....
  2. B

    tilt and trim

    1989 evinrude 48 h p. Can i put tilt and trim on this motor. It has manual lift and for this old man it is all i can do to lift it. Been looking for it here on i-boats but no luck. Any body that has that motor give me some advice? This is all new to me, this motor. Thanks for any...
  3. B

    evinrude 48 h p year

    Another what year guestion...Mod #. E48ESLCR.....evinrude.. Just bought a pontoon with it on it. Any remarks about that motor and I would like to know the year to buy parts if needed. Thanks .....Bsandy....
  4. B

    carb rebuild

    How much would I expect to pay for carb rebuild for a 9-9 evinrude? Thanks....bsandy..
  5. B

    prop removal

    Just bought a 2 hp evinrude (2520) 1975. I want to take the prop off to run it in water but the key won't come out. I have tried every thing I know and it just will not budge. Any body had that problem?? Would I be able to drill it out? .....Bsandy.....
  6. B

    evinrude 2 h. p.

    Just picked up 2 horse evinrude at a yard sale. Mod.#25020 Ser.#e0002325 The spark plug wire wasn't touching the plug, fixed that and it took right off. Looks like a good buy for $3o. Can any one tell me what year it is???Sure would like to know and Thanks. ....Bsandy.....
  7. B

    long shaft on 15" stearn

    I want to tow my pontoon to the boat ramp(about a mile) and I have a !4 ft. alu. boat with 15" transom and a 10 H P motor with long shaft. Would it work slow speed.? These darn motors are heavy for a old man and i would like to know if it would work before I put it on. Thanks ahead of time...
  8. B

    fuel pump Help

    I messed up good this time. I took the fuel pump off a 1973 18 h P Evinrude thinking I could rebuild it. Now i have parts i don't know how to put back together and if iwas to buy a new one what holds it together to put it on the motor. I sure goofed....BSandy
  9. B

    Johnson 2.3 questions

    Got this little motor on a trade. It is Johnson 2.3 Mod.#hj2renr Ser.# h9272405 Made by Outboard Marine Corp. Hong kong . What is the year..fuel mix..plug and breaker settings..And is it a air cooled? Lot of guestions but will be thankfull for answers....BSandy
  10. B

    73 evinrude,don't seem to be getting gas

    73 evinrude 18 h p electric start. No ser. # on motor. I bought this pontoon that has been setting since 2002. First off it didn't have fire to the plugs. I pulled the flywheel and the key was sheared so i put new points and condenser. It ran pretty good in barrel so i put it in the water. On...
  11. B

    4-stroke oil ?

    Nissan says use only oil with api rateing of sf, sg, sh, or sj. for 4 stroke engine. Pennzoil has a marine premium outboard oil for 4-cycle. It claims to meet or exceed requirements where NMMA FC-W Sae is recommended. These letters confuse me. Is it safe to use the Pennzoil? Thanks...
  12. B

    new nissan four-stroke ?

    I am buying a 15 H P four-stroke NISSAN long shaft with electric start (2008). Never had four-stroke before. Has any one got one that can give me info on what to expect from this engine? It will go on a 14 ft. alu.semi v fishing boat (sylvan). I do a lot of trolling, do they run pretty smooth...
  13. B

    dogs down at half speed

    I have 9-9 h.p. evinrude mod. # e10re1r. It has been sitting over 6 months with out running.I put fresh gas in it and it starts great. It trolls good also but any more than half speed it will dog down to idle. Runs great up to half speed. I think it is a 1995.Any tips where to start would be...
Top