Search results

  1. C

    Will Not Start Due To Grounding Problem??

    1995, 75 hp force by mercury--My cd units are grounded and motor will not start. I can disconnect the black/ yellow wire and motor cranks and runs good. However I can only turn the motor off by reconnected the black/yellow wire to the cd units. How can i get control of when I want to ground...
  2. C

    1997 Force 75 HP motor Lift Problem

    My lift motor is good, but the pump right below is leaking. Can you buy a kit to rebuilt the pump? If you can Where? If it is not rebuiltable where can I buy a pump to replace mine? Thanks for any help.
  3. C

    power tilt problem on 1997 , Force 75 HP

    Motor run on power tilt, reservior is full of fluid. Cylinder on lift is not leaking and no line leaks. Problem is though, that nothing happens when the lift is actived and motor runs. Any suggestions?
  4. C

    Force 75ELPT

    I just bought a 1997 , 75HP elpt , Force by Mercury motor. Is this motor a mercury or a Chrysler? Who manufactured the motor? The motor appears to be in good condition, but is it worth the trouble of installing on my boat? NADA list this motors value at less than $400.00. NADA list the...
  5. C

    60 HP Yamaha ??

    What should be the compression on a 2004 model Yamaha 60 HP. thanks
  6. C

    Motor Runs Away!!! Unusual Situation!

    1992, 40 HP Johnson. Cranks excellent. Idles OK; Give it the throttle it goes in gear , then motor Reves up to a very high speed. Pull throttle back and it still stays reved up. The butter fly valves are closed while this is going on. The ignition switch will not shut the engine down, the...
  7. C

    WTB- tilt and trim

    see the iboat store. buying, selling etc are not allowed on the forum. TD http://forums.iboats.com/showthread.php?t=231537
  8. C

    Want to buy!

    EDIT: Sorry, Chodie. No buying or selling is allowed. JB
  9. C

    Johnson Touch Trim Problem?

    I purchased a 40 HP 92 model Johnson and the plastic (Shell) that attached around the ball on the lever was broken. I replaced this piece and I have adjusted the play on the lever to specs and every other way and I cannot get the ram to move out of the cylinder in an upward direction. What is...
  10. C

    Touch Trim Problem?

    I have a 92 johnson 40 hp. I just replaced the plastic (shell) that attaches to the cable on one end and to the round ball on the lever. When I push the lever to the position to raise the motor I can't move the motor very far to the up position. In other words the cylinder is not moving and...
  11. C

    Johnson Model No. or Serial No. ??

    J0003138 This is on the plate for a 40 HP Johnson motor. Anyone recognize this? Is it a commercial engine? It has 3 skegs on the lower unit and the prop seems smaller in diameter than a regular unit. Comments will be appreciated. thanks
  12. C

    Need help on part for manual raising motor

    I have a 92 model 40 HP, model no. T J40ELENM. This is a no power lift motor. It is manual lift. Their is a lever or handle on the right side that unlocks the motor so it can be manual lifted. Attached to this leaver is a cable that runs to something that unlocks the lift mechism. My cable...
  13. C

    1975 4 hp Johnson won't start ?

    Motor has set up awhile. Have good spark at plugs, rebuilt carb and have fuel in carb. compression about 95 on each cylinder. Engine will not start. Checked for vaccum at carb and I have none when I try to start motor. What is the problem?
  14. C

    55 HP Nissan Idle problem?

    My 55 HP nissan (purchased used 6 months ago) will not idle smooth. My dealer tells me that this is common problem with these motors and their is not way to repair. Anyone know how to make it idle better? Thanks, Chodie
  15. C

    Seafoam and my Nissan motor

    My 55 hp nissan has been setting up for a while. It doesn't run good at idel or low speed. Runs excellent at high speed. Will seafoam in the gas help? Will seafoam hurt the engine? thanks for your help
  16. C

    1995 40 HP force engine

    Is the 1995 40 hp force engine the same as a mercury engine? If not , is it the same quality as a mercury engine? I am totally confused about force versus mercury engines. any help appreicated.
  17. C

    1987 Grumman 17' Outlaw

    How well does this boat handle choppy water and wind? Are these well made boats? thanks for any information
  18. C

    Mercury 40 Hp without tilt and trim

    Is it hard to operate a 40 hp motor not equipted with tilt and trim? thanks for your help
  19. C

    1995 mercury 40 HP tilt and trim?

    I have a 1995 merc 40 hp that does not have tilt and trim. Can this be added and where do I purcase equipment? thanks , chodie
  20. C

    97 model 75 HP Mercury

    Did the 97 model 75 hp come out with oil injection? If so when was the first year oil injection came out on the 75 HP engine? Thanks for your help
Top