Search results

  1. E

    95 honda blows fuze

    when battery is connected, 15 amp fuze blows. can rectifier cause problem? how can i tell?
  2. E

    Overrev Limiter

    Have a Honda, 15 HP, BF15 outboard. Operator manual stses there is an overrev limiter. Where is it located and how does it work?
  3. E

    Water Pump Removal

    Have a 2007, BF15D, model BALJ-1402007 and need to pull lower unit to remove/replace water pump. Other than 4 bolts near bottom, I think the shifting rod must be "unpinned" to allow unit to drop. Please advise. Also, cannot locate an on line parts distributor for 2007 outboard! Only 2006 and...
  4. E

    Parts for Honda BF15D

    Looking to buy parts online for subject outboard
  5. E

    Water Stream Dribble

    Have 2007, 15 HP Honda. Stream is only a dribble. Does not overheat. What is normal stream?
  6. E

    Intermediate Jet/Orifice Adjustment on 1984 50 HP

    Have a 1984, 50 HP, BELCRM. After reading Seloc manual, I concluded the carbs are type 4, with fixed low, intermediate and high speed orifices. Carbs have adjusting needle screws for intermediate orifice. Manual dose not mention adjustment for intermediate orifice needle screw. What is the...
  7. E

    Best Shop Manual for 50 HP, 1984

    What's the best manual to get for an Evinrude, 1984, 50 HP? Thankyou
  8. E

    Tilter for 1984 Evinrude 50 HP

    Can an outboard motor tilter work on the subject outboard motor without damaging the engine cover? Thanks Ed
  9. E

    1984 Evirrude 50 HP Temp Horn sounding

    Have Model BELCRM Am operating it in 55 gallon barrel that had diesel fuel in it. Cleaned barrel, but dirty and greasy residue forms on water surface and motor. Flow from pee-hole occurs within minute after starting motor. Water feels warm but not hot. Greater flow when revved up. Horn...
  10. E

    Idle Speed for 1984 Evinrude, 50 HP

    Engine is BELCRM. Idle rpm, no load, is 2000. Seems too high. Revs up good with no load. What is correct idle rpm? If too high, what is procedure for adjusting screw for each carb to get rpm to nominal? Thankyou Ed
  11. E

    Fuel Primer for 1984 50 HP Evinrude

    Does primer squirt fuel into carb throat when key is pushed up? Or should key be pushed and held to prime while starting?
  12. E

    Cross Section View of Carb for 1984 50 HP Evinrude

    Looking for diagram that shows air and fuel passages in carb for 1984, Evinrude 50 HP, BELCRM
  13. E

    84 HP Evinrude Stall under load

    In a barrel, when throttle linkage is rotated to rev engine, it "chokes out". Looks like only 2 adjustments. Are they low speed/idle? Input requested? Gracias Ed
  14. E

    Spark Plug and Gap for 84 Evinrude

    In BAJA with no access to manuals. What type plug (and gap) is used in 1984 Evinrude, 50 HP, model BELCRM?
  15. E

    Carb Adjustment Procedure for 50 HP Evirude

    Would like to obtain procedure for adjusting carburetors on 1984 Evinrude, 50 HP. Thankyou
  16. E

    Wiring diagram for 2002 Bayrunner open

    I'm in BAJA and cannot have manual delivered. Looking to download a wiring diagram for 2002 Bayrunner. Thankyou Ed Jeatte@man.com
  17. E

    Wiring diagram for Evinrude 50 HP, 1984

    Would like to download a wiring diagram for 1984, 50 HP Evinrude - E50BELCRM. I'm in BAJA and unable to have service manual delivered. Thankyou Ed Jeatte@msn.com
Top