Search results

  1. S

    No water flow to heater at idle (96 350 mercruiser)

    There is no water flow to my heater on my maxum when the engine is at idle. Once up to 1200 rpm then the flow is fine.<br /><br />I've checked the raw water pump impellor today and it looks good as new. <br /><br />Any suggestions?
  2. S

    Turn cap clockwise or counter clockwise to advance timing?

    350 mag. Looking down on the cap from above am I turning clockwise or counter clockwise to advance the timing?<br /><br />Thanks in advance.<br /><br />Also does anyone know is the thunderbolt 1V / V ignition is similar in any way to a standard GM ignition or do mercruiser use a totally...
  3. S

    wiring diagram for 96 350 magnum TBI ?

    Anyone got an engine wiring diagram for the above?
  4. S

    mercruiser 350 magnum efi, possible propane conversion.

    Hi Guys,<br /><br />I'm here in the UK where we are currently paying over $8 a gallon on gas.<br /><br />I have been running cars and boats on propane for a while as its less than have the price of gas.<br /><br />On my last boat (which I just sold) I had an impco propane carb sat upon holley...
  5. S

    Starter motor for circa 88 5.0 mercruiser

    The starter is shot on my mercruiser.<br /><br />When cold its fine but as soon as the engine warms it just wont turn.<br /><br />All the merc starters I see on the net loo different to mine.<br /><br />Mine has two bolt holes on the flange at opposite sides and mounts on the right hand side of...
  6. S

    How many temp sensors on 5.0 mercruiser?

    I have a circa 1988 5.0 mercruiser and it seems to have 3 engine temp sensors. Is this normal. There is on on the engine water pump, one on the top of the inlet manifold and one at the rear of the engine.<br /><br />The reason I'm asking is beacuse I need to remove the one on the water pump to...
  7. S

    Thunderbolt IV ignition advance. How to tell if working?

    How can I tell if my ignition advance is working?<br />I'm assuming its mechanical advance on the distributor.<br /><br />Thanks<br /><br />Jay
  8. S

    Problems with mercruiser 5.0 lack of power, bogging etc.

    Looking at a friends inboard ski boat with the 5.0 mercruiser model MTE230.<br /><br />The boat had not been used for a few years when he got it so we did compression check - 6 @ 150+, 1 @ 140 and 1 @ 130 but the low ones went up with a little oil.<br /><br />Put on new leads, plugs, cap and arm...
  9. S

    5.0 Mercruiser compression readings

    Friend just got a new boat with this engine.<br /><br />I ran the test with the engine cold.<br />6 cylinders at 155 Psi<br />1 at 140<br />1 at 130<br /><br />Anything to worry about? The 2 lower readings were not next to each other and both went up with a little oil in the bores.<br /><br...
  10. S

    Quadrajet junked, are Mercarb's any good?

    Got a mercruiser 5.0 in a small british ski boat. After stripping, cleaning and rebuilding the standard quadrajet it still runs poor. No acceleration and lumpy with poor starting.<br /><br />So I think the carb is junk.<br /><br />(timing is good, new cap, arm and leads etc)<br /><br />Been...
  11. S

    Merc Exhaust manifold water flow

    Got a 5.0 Mercruiser engine in a ski boat and its the first inboard I have seen with two sets of water pipes going to the manifolds.<br /><br />Looks like water enters the manifolds at the front like normal but also there is a hose going to the bottom of the manifold in the middle also. <br...
  12. S

    Will a trim/tilt from a 115HP fit my 80HP merc?

    Trim tilt unit on my 1987 80HP merc (3 cyl) is trashed.<br />Been offered a complete unit from a same year 115HP.<br /><br />Looks very similar in the photo but not sure if its a direct replacement.<br /><br />Anyone know?
  13. S

    Best prop for wakeboarding with a 80HP merc?

    Looking to change to prop on my merc. It has the factory fitted 3 blade prop (not sure what pitch).<br /><br />I would like something lower pitched as when I'm going 20mph its right in the flat spot of the rev range just before the power band starts and as such its hard to keep a constant...
  14. S

    80HP Merc wont warm up and poor running problems

    Hi,<br /><br />New to this outboard game, more used to inboards but helping a friend with his newly purchased boat.<br />Circa 1988 3 cylinder 80HP merc. Has stood for 3 years un used.<br />Starts up ok but stalls when you give it some thottle.<br />Had it ticking over in the water today for...
Top