Search results

  1. S

    action craft 1820 self bailing question

    on a 1999 action craft 1820 there are two self bailer holes in the floor on each side of the boat. one goes directly through the side of the boat and other goes down into the floor. why is there two? does the one in the floor drain into the bilge? do you normally plug the side holes when...
  2. S

    Prop too high rake??

    2004 18cc sea pro with a f115 yamaha turning a Stiletto 13 1/4 x 17 SS prop. max 5500 to 5600 rpm at about 43 mph. Boat performs decent, but seem that the motor has to be trimmed down pretty far to keep it from porpoising. im also using trim tabs, but im thinking that the prop may be trying...
  3. S

    F115 cranking issues. Im lost on this one.

    2003 yamaha F115 TLRC. engine cranks on the first try everytime when its cold. After i run it for a few minutes... stop.... fish.... then go to crank it up it takes 3 or 4 tries before it will start. It only does it when the engine is warm. its sounds exactly like a weak battery, but the...
  4. S

    Need some bow rail plugs.

    Just installed a trolling motor on my center console and had to cut a portion of the bow rail.. anyone know where i can get some plugs or bullet end style caps for the bow rails. this is all i could find. http://www.bosunsupplies.com/products2.cfm?product=S3679
  5. S

    Can i Use 2 different amp hour rating batteries for 24v trolling motor?

    I have limited space for batteries,so i can only go so big. i already have one deep cycle that i used for my radio, so i will just buy one more and hook them together for trolling motor. Can i use two different amp per hour rating batteries and still wire them in series? I would use the 24v...
  6. S

    Arrrgghhhhh! Frustrating shaft length issues!

    I read many places that to get proper shaft length you measure from mounting surface to top of water and add 12" or add lil extra for chop..... I have 28" from mounting surface to top of water. So i doubled the 12" and added and extra 24" because of chop. that gave me a total measure of 52"...
  7. S

    Minkota Riptide stowing question

    On the minkota riptide bowgaurd360 mount and 52" shaft(hand tiller) i can only lower the motor like and inch or so and the actual lower motor portion does not sit on the mount support.it is out past it. Is the shaft desinged to slide up when you are stowing so that the motor will sit properly...
  8. S

    PVC pipe in hull for running wires?

    Does anyone know where the pvc pipes are for running the wires through? the boat is a 2004 sea pro 18' cc
  9. S

    Need some sugg. on which trolling motor for 18CC.

    Looking to put a trolling motor on my 18' cc sea pro. anyone have any suggestions on what length shaft and thrust? Im looking at the 80lb thrust and probably the 60" shaft. im not sure if the 50" shaft will be long enough. I have already decided to go with hand tiller. Best suits my...
  10. S

    FS. Stiletto prop fits yamaha

    No selling on the forums. Use the classifieds for that.
  11. S

    Need Prop pitch help.

    I have a 2004 18' cc sea pro(equivalent to new18'seaboss) with a yamaha 115 four stroke. When i got the boat it had a 13 1/4 x 17 aluminum k series prop that turned 6200 rpm with full tank and 1 person trimmed all the way up. The prop was slightly bent so i went to a stainless steel stiletto 13...
  12. S

    Need prop pitch help with 18'cc sea pro.

    I have a 2004 18' cc sea pro(equivalent to new18'seaboss) with a yamaha 115 four stroke. When i got the boat it had a 13 1/4 x 17 aluminum k series prop that turned 6200 rpm with full tank and 1 person trimmed all the way up. The prop was slightly bent so i went to a stainless steel stiletto 13...
Top