Search results

  1. Y

    130ETLF Greasing Upper Midsection

    I recently pulled this motor out of retirement due to a bad lower unit. I pumped some grease to the midsection through the grease zerk about halway up the midsection. All the grease I pumped in came out of the bottom. What should I do to get some grease to go up instead of down? [/URL]
  2. Y

    4 wire trim guage 3 wire sending unit?

    I am working with a 1989 130 HP Yamaha. The guage comes from a 1984 90 yamaha. The guage hae a 4 wire harness coming from it, but the sending unit at the motor only has 3 wires. I am left with an extra gray wire. Is there a way to make these ccompatable? Thanks, David
  3. Y

    1989 130 lower unit install

    I have my lower off of the motor. Is there any certain procedure to put it back on? Does it need to be in forward or neutral?
  4. Y

    is the is compression range acceptable

    I have the option to purchase a 1996 115 Johnson. The guy that has it says the compression is between 105 and 120 across all 4 cylinders. Should I be concerned that at least one cylinder is at 105?
  5. Y

    is the is compression range acceptable

    I have the option to purchase a 1996 115 Johnson. The guy that has it says the compression is between 105 and 120 across all 4 cylinders. Should I be concerned that at least one cylinder is at 105?
  6. Y

    O-Ring Driveshaft 1991 70HP evinrude

    I cannot figure out where to put part number 58 in the diagram below. The water pump repair kit came with two orings. The guy at the parts counter said to go with the one that fits the drive shaft better. But where does it go?
  7. Y

    Galded threads on lower unit

    I have some galded threads in the lower drainplug on my 1991 70hp Johnson. The plug was tight. Once it broke loose it backed out like normal. When I went to put it back in it would tighten as soon as it started. I can see that the threads are all galded up. How would ya'll go about fixing them?
  8. Y

    How do I wire up my alarm buzzer?

    The light colored wire looks yellow in the pic. It is actually brown. The wires going into the key switch are as follows: Purple Purple w/ white stripe Black w/ yellow stripe Yellow w/ red stripe Red Black There are another two wires in the harness coming from the motor. One is grey...
  9. Y

    Which Contol cables do I need?

    I recently picked up a 1990 70HP Evinrude. The motor came with an older Power Pilot control box with no cables. I went to my local Evinrude dealer to pick up the cables. When I described what I needed he started telling me that this motor shouldn't have the type of connection I was...
  10. Y

    Power Pilot Help

    I am trying to move the shift/throttle lever from the left side to the right side. This is as far as I am able to dissassemble. How do I seperate the plastic piece from the shift /throttle lever? Here are a few more pics for reference. Thanks in advance for any help.
  11. Y

    Help Getting model number

    I picked up an Evinrude 25. The tag on the bracket is gone. The freeze plug has R8571249 stamped on it. I cannot find the model number. Can someone please direct me to a model number so that I can get parts? Right now I need a breather that mounts to the carb. Thanks, David
  12. Y

    Overheating Manifold 1998 350

    I recently acquired a mercruiser. The engine serial is 0L037276. When I run it the starboard exhaust manifold gets too hot to touch, and the port exhaust manifold is cool to the touch. I took the starboard manifold and elbow off. I then seperated the elbow from the manifold. I found some...
  13. Y

    Cooling System test

    I am working with a 1998 5.7L ALPHA GEN+ engine paired to a 1998 ALPHA ONE GEN 2 outdrive. This boat has been sitting for a few years, and I am clueless when it comes to mercruisers. I have been warned that the exhaust manifolds might be clogged. How do I go about checking for this? I did...
  14. Y

    Which Manual do I need?

    My outdrive serial # is 0L105557 My engine serial # is 0L037276 Also how can I derive the age of each part. I know the boat originally came with a jet drive, so I assume the drive is newer. Thanks for any help
  15. Y

    Airtex Brand, part no. 110-E11004

    After stumbling upon this fuel pump and understanding it to be an exact replacement for mercruiser part #861156A, I ordered it from Summit Racing. The outlet side of the airtex has no threads. The factory pump has a crossover that goes between the fuel line and the pump. Any ideas how I should...
  16. Y

    Mercruiser fuel pump wires

    I recently purchased a 5.7 mercruiser serial # 0L037276 from the company I work for. A guy who doesn't work here anymore had swiped the fuel pump. When he took the fuel pump it looks like he cut the plug on the engine side. There are two sets of wires in the area where the fuel pump appears...
  17. Y

    Opinion on 48 Mariner

    I am thinking about purchasing this motor. The guy says it is a 93 model. Does it look to be about a 93 model? Are these motors known to have lots of little problems, or are they know for being tough and dependable? Should I expect parts to be readily available? Also, any estimates on a...
  18. Y

    Resitor spark Plugs od Non Resistor Plugs

    It is time to change the plugs for the first time in a newly aquired rebuilt engine. The engine is a 1989 130 yamaha. The sticker under the cowling calls for B9HS-10 plugs. I went to local yamaha shop and they gave BR8HS-10 plugs. When I realized these weren't the right plugs I exchanged...
  19. Y

    Temp Sensor Question

    I have an 89 130HP yamaha. I just got this engine and thought I should test the temp sensors. I unpluged the sensors, connected the two plugs on the wire harness side, and turned the key on. The buzzer did not go off. I pulled the buzzer from the control box and attached it to the battery...
  20. Y

    Anyone have an extra control box???

    I recently purchased a 1989 130 yamaha. The engine did not come with controls so I am looking for a control box with a reasonable price tag. Thanks for any help.
Top