Search results

  1. 1

    Thermostat Housing Rebuild

    Thanks for that! I’ll give it a try.
  2. 1

    Thermostat Housing Rebuild

    It’s not reading on the Gauge. Faria gauge.
  3. 1

    Thermostat Housing Rebuild

    Went without any Gasket sealer in the end. All went back together mint. And we’ve now got a functioning Thermostat and it’s reading around 160 on the Temp Gauge! Now to get the Tach working 🤦‍♂️
  4. 1

    Thermostat Housing Rebuild

    Thanks guys.
  5. 1

    Thermostat Housing Rebuild

    Thanks guys.
  6. 1

    Thermostat Housing Rebuild

    We’re replacing parts 7,8,9,10. Cheers
  7. 1

    Thermostat Housing Rebuild

    Thanks!
  8. 1

    Thermostat Housing Rebuild

    Part #864592T
  9. 1

    Thermostat Housing Rebuild

    Hi Team Rebuilding the Thermostat Housing on our 4.3l V6. Question, Gasket Cement on the Cork Gasket that goes into the Housing before the Thermostat goes in? And same question for the Gasket that has the Brass Inserts that goes between the Thermostat Housing and the Motor Body? Thanks Again
  10. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Thanks, but I wouldn’t have said it now mysteriously works? We spent a fair bit of time eliminating a bunch of potential reasons, and the conclusion we came to was that It seemed that there was either a Vacuum in the Fuel Line, or there was something stuck inside the Fuel Pump. The Boat had been...
  11. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    No. We did not. But the symptoms seemed to be pointing (eventually) to the Fuel Pump. Where is the Anti-Siphon Valve? And how would one check it? Thanks
  12. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Update… And thanks to all for suggestions and help! Having established that we had power going to the pump, but the pump not working. We removed the Fuel Pump and Lines. We then powered the pump without any lines attached and it ran!! It would seem that somewhere in the process of removing, we...
  13. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Update… Have grounded the Blue wire from the Oil Sender & Oil Gauge maxed out. Removed the Oil Sender, cleaned it up (was a bit messy looking around the base) Cranked the motor with the Oil Sender removed, Oil pumped out. Reinstalled the Oil Sender, connected wire, Cranked the Motor and Oil...
  14. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Into the Pressure Switch Plug? And if it doesn’t run?
  15. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Hey there. Based on the Serial number, we’re pretty sure it’s a Carb.
  16. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Thanks… So just to clarify 🤦‍♂️ #8 is the Oil Sender for the Gauge at the Helm (makes the Oil Gauge work on the Helm) #10 is the Pressure Switch for the Fuel Pump (as in post #5) and sends signal to the Fuel Pump to turn on. #34 is Switch for the Alarm for Oil Pressure (definitely working!!) 8...
  17. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    And this is the pressure Sensor? One Lighter Blue wire coming out of the top of it with a push on plug
  18. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    And this is the plug that came off it. Look correct?
  19. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    So this is the pressure switch? Yes?
  20. 1

    2006 Mercruiser 4.3 no power to Fuel Pump

    Thanks! Will try that and report back. Cheers
Top