Search results

  1. vincechig1975

    89 Alpha won't go back on. ...Help!

    I have an 89 Glastron SS 195 Sierra 3.0 , Alpha 1 outdrive. I tried aligning the shift shafts back up and the lower will not go straight again. I don't want to force it and wind up breaking it. What am I missing? Should I just take it to the shop?
  2. vincechig1975

    trim/tilt issue (s)

    I recently posted about having a try tilt issue, well I'm wondering if I might have another issue instead of the pump being the culprit. Is it possible that there may actually be a line partially blocked, if so how can I check while they're still on the boat. .....any ideas or suggestions?
  3. vincechig1975

    trim/tilt issue (s)

    I have replaced my trim cylinders, and the pump today and the new problems are cylinders go up very slow and the outdrive won't stay up. Frustrated beyond belief.
  4. vincechig1975

    trim/tilt issue (s)

    I recently purchased a 1988 Glastron Sierra 3.0 Alpha One outdrive and took it out Saturday and it was awesome, but Sunday we took her back out and my trim would go down but not up except when you use the trailer button. I'm not sure what's going on in this case, so any help would be great. He...
  5. vincechig1975

    Alternator swap

    Can I swap the alternator from dead 2.5l to my fresh 3.7l if so what modifications are necessary to do so?
  6. vincechig1975

    88 2.5 won't start, Please help!!!!

    I have an 88 2.5 l that I have checked everything electrical. Checked the switch on top of the valve cover, and took out both batteries and load tested then both they checked out good. All connections are tight and just to be sure I checked out the battery terminal ends found one set of bad...
  7. vincechig1975

    88 2.5l starter issue

    I am working on an 88 2.5l Mercruiser, I just finished charging the batteries, and installed them accordingly, after the installation I checked all my connections to make sure they were tight, and then checked the systems, one by one they lit up and worked and then went to start the...
  8. vincechig1975

    1.98.1 nd 1.84.1 out drives

    I am going to do an engine swap here from a2.5 to my 470 along with the out drives as well, and I am wondering what are the differences between these drives, shaft diameter, gear ratio ( is one of the differences) , I bit more education with this one fellas. I am also wondering if I can just put...
  9. vincechig1975

    Engine swap/ outdrive swap

    I am getting ready to swap out my 2.5 for a 3.7 including outdrive.....should I change the gimble bearing as well? What about the alignment in this case, I know I will need the tool as well, this is the fist time I've done this one. After I hook everything up again, before installing the...
  10. vincechig1975

    88 Smoker Craft

    Re: 88 Smoker Craft Here's the photos of the cuddy's instrument panel
  11. vincechig1975

    88 Smoker Craft

    Re: 88 Smoker Craft Here's photos of the instrument panel in the cuddy
  12. vincechig1975

    88 Smoker Craft

    Wife and I bought an 88 Smoker Craft open bow today and it has a 2.5 l in it, I was wondering if my 470 would work in it's place since it's a knockin really bad and I have a 4.3 to go into the cuddy we have . It is an alpha drive and I know the inner plate and coupler will need swapped around...
  13. vincechig1975

    Extra wires.......?

    I have an 88 470 and I finished (almost) the wiring harness connections now on the rear of the engine in the area of the cooler, but behind the starter, there are 2 wires and black and a white with a stripe ...... where in the world do they go. I have hooked everything else up that can be but...
  14. vincechig1975

    470 cooling system, need educated

    I searched the threads for information on the 470 cooling system and well haven't found anything on it,like normal late at night and half asleep. From what I can see it's possibly a closed cooling system is this right? Having a thermostat in it would indicate it's closed and all that the raw...
  15. vincechig1975

    Trim Cylinders.....

    Re: Trim Cylinders..... I checked em out there's like 4 different one's....here's some numbers that may help
  16. vincechig1975

    Trim Cylinders.....

    Re: Trim Cylinders..... I looked at the parts for them and there are like 4 different kits for Alpha's (Alpha 1) it's not an SS just plain Alpha year model 88. here's some numbers hope we can narrow this down.
  17. vincechig1975

    Trim Cylinders.....

    I was just wondering if you guys had a link for the blow up diagram of the trim cylinders for an Alpha....? I searched but am not able to find the right one so I guess I have to do a match up by diagram, here's a pic that might help narrow it down.....
  18. vincechig1975

    This an issue...470 fuel pump

    I am getting ready to put the fuel pump back on the engine, and well it did have the spacer and a gasket on it origionally but is it really necessary to put the gasket back on as thin as it is with that thick spacer ? This came with it when I removed it so is the spacer actually taking up about...
  19. vincechig1975

    Distrubutor wire.....470 Alpha

    I was wondering which side of the coil the distributor wire gets mounted to? The positive or negative? When I took it off I didn't take a photo but yet the photo I did take earlier in the tear down process I can't seem to find right at this point. Now I know the tach gets put on the Neg side or...
  20. vincechig1975

    Power steering , to add one or not......

    I am beginning to resume the tear down phase of our boat ( 88 Cobia Cuddy) and origionally did not have power assist steering or anything for power steering, I have been toying with the idea of adding a unit ...but.... not sure of what I will need and where I could find the correct one for this...
Top