Search results

  1. P

    1989 OMC V6 distributor shaft gear

    A friend of mine has a 1989 OMC V6 that quit running. Found the distributor shaft gear is worn down to not turning the distributor. Is this a special gear or would any 198X Chevy V6 distributor gear fit & work correctly ?
  2. P

    1981 Chryslert 20 HP Prop Troque

    Does anyone out there know whether a 1981 20 HP Chrysler Outboard has an adjustable Trim Tab to combat Prop Torque? If there is no adjustment, are there suggestions on cheapest & easiest way to address the problem? 1981 20 HP Chrysler on 14 ft flat bottom Aluminum boat.
  3. P

    Where can I find parts

    I need points and condensers for a 1981 Chrysler 20hp (I think made by Mercury) model # 202H1M. Various sites say OEM parts are F12153-1 for points and F12181-1 for condenser. SIERRA 18-5161 for points and 18-5241 for condenser. OEM kit FK1066 and SIERRA 18-5009 are supposed to contain all I...
  4. P

    09 yamaha 25esh flooding

    Here's a picture of the SIERRA part vs the OEM part.
  5. P

    20 Hp Chrysler

    I have just come upon an outboard having cowling from a 20 hp Chrysler. On the power head it has RW504222 stamped. All other ID plates that I can find are worn & not readable. I'm wondering what I have (HP, Year, etc..) so I can establish a value and buy parts. Any help is...
  6. P

    1974 -- 110 (9.8) Pinging

    My dad says that his 110 (9.8) 1974ish outboard has started pinging. I haven't heard this myself but his description makes it seem like a 4 cycle labort knock. He's trying to blame the Ignition Control Box as some of the wiring has coroded isulation. Any ideas or suggestions are welcome.
  7. P

    1968 - 18 hp - float 375919 <-> 0396514

    i have a 1968 - 18 hp evinrude. i just rebuilt the carurator with a 0396514 float (the varnish coat had deterorated off the cork float). Now at when I try to go wide open the motor will speed up then slow down a few times then try to die. I'm pretty confident that I have all the trash...
  8. P

    Red Hot Ground Jumper

    on a 2009, 25 hp, 2 stroke.... was wiring lights to the boat (aluminum). touched only one light wire to the hot battery post... the ground jumper on the motor, behind the transom sparked and got red hot. apparently the light was wired in such a way it caused a dead short back through the...
  9. P

    Serial Number Xref

    Can anyone point me to a serial number cross reference and/or tell me about a Model 40 (4 hp) Mercury 3298796 ?
  10. P

    iboats marine

    does this message belong here ? did my first business with iboats marine this past week. sierra fuel pump 1/2 local oem price. shipping included. only two drawbacks..... had to wait 3 days for UPS to bring the part to my door and my local gov didn't get their share. IBoats ...
  11. P

    Prop Nut

    Is there a torque spec for the prop nut on 197x, 18 - 25 hp johnson / evinrude ?
  12. P

    Need Help Finding Old Part Numbers

    Can anyone help me find part numbers for old Johnson & Evinrudes ? The BRP site only goes back to like 1968. Specifically, I'm looking for the part number for a 1958, 7.5 Johnson Gear & Shaft part (the gear and shaft in the tiller to work the throttle) which looks ALOT like the one I need...
  13. P

    25hp dies at full throttle

    1973, 25 Evinrude Runs fine from idle to WOT. After a short time it slows down to an idle coughs/sneezes and sometimes dies. Will idle or low rpm for as long a you want it to. I put a new float and valve in the carb which looked brand new inside. When it starts to slow down, I squeeze...
  14. P

    Transom Mount (1976, 9.9)

    Will a 1968 - 1973, 9.5 Transom Mount fit on a 1974 - 1976, 9.9 ? Both Evinrude. Part #s are different but parts look very similar.
  15. P

    CDI Spark Problem -- Help Needed

    1976 (10624G) 9.9 Evinrude with a CDI type ignition from a later model, assumed to be, 1977. The motor would run up to half throttle and die. Both stop switch wires have been been cut away from the plug to the power pack. The plugs on the power pack wires to the coils have been replaced. Here...
  16. P

    1976 / 77 -- 9.9 Hybrid -- CDI Ignition Questions

    Hold on to your hats...... 1976 (10624G) 9.9 Evinrude with a magneto/electronic ignition from a later model, assumed to be, 1977. The motor would run up to half throttle and die. Both stop switch wires have been been cut away from the plug to the power pack. The plugs on the power pack...
  17. P

    Gold Anniv 6hp.. starving for air

    Well folks, I ran across a strange one while working on a motor my brother-in-law just bought... it's a 1972, 6hp, 50th anniv series. Like new. BIL couldn't get it started after he bought it. So, I checked it out, cleaned the carb (stuck float wouldn't allow gas to bowl) got it running...
  18. P

    72 Johnson, 6hp Carb, High Speed

    Is there any high speed mixture adjustment hidden behind a plug or somewhere on the 1972, 6hp, Johnsons ?
  19. P

    Propeller Questions

    I have a 1976, 6hp Evinrude. It runs good and is fairly quick pushing a 12ft flatbottom, alluminum jon boat. However, I'd like for it to go a bit faster and plane out a bit better. I was looking at the BRP site and noticed that the 6hp of different years specify different props. Mine has a...
  20. P

    7.5 Johnson / Evinrude

    Can any one tell me some about 7.5 hp Johnsons / Evinrudes like what year did they quit making them, are they good motors, are parts still available ... etc. Thanks....
Top