Search results

  1. F

    loose wires 90 HP Mercury 3 cylinder

    What is an OT sensor? And should the tan wire be plugged in to the brown and white wire?
  2. F

    loose wires 90 HP Mercury 3 cylinder

    I replaced the oil reservoir tank and noticed 3 loose wires. Motor is new to me as of a year ago and runs fine. Anyone have any idea what they are for?
  3. F

    convince me to get or not get an I/O over an outboard.

    Only boat I've owned was an outboard deck boat (15 years). Sold it a few years ago and looking to get a newer deck boat. Looking at used 4 stroke deck boats like Hurricane. Problem is there are not very many of them for sale in the Houston area. Seems most boats are I/O. I'll be doing all...
  4. F

    Pontoon regrets?

    We currently have an old 16ft deck boat and are looking to replace it with something newer, nicer, and larger. We are considering deckboats, open bows, and pontoons. We mainly like to cruise or just float, but also like to do a little bit of tubing and skiing. Anyone have any regrets going to...
  5. F

    No high speed for first few minutes

    1979 Evinrude 115. Rebuilt the motor last year, has about 100 hours on it. The last few weekends I have taken the boat out it will not run full speed for the first few minutes. This is only the first few minutes on the first day. Once the high speed jets kick in it runs great for the rest of the...
  6. F

    some observations...

    I've noticed every time someone asks "can I tow this boat with this car" people always chime in about needing a truck, not a car. The reasons are varied, but none make any sense. Some common things said are: 1. The car is not heavy enough to stop the boat/trailer in an emergency. Really? So a...
  7. F

    Why double the oil for break in but not synthetic?

    Why during break in of a rebuilt motor can you not use synthetic oil in fear of too much lubrication not seating the rings properly...but it is recommended to use double the regular oil for extra lubrication. Or am I missing something?
  8. F

    How to determine prop size?

    How do you determine what size prop you have when there are no markings? Is it the total diameter of the fins?
  9. F

    Odd temp horn issue

    1979 115hp Evinrude. The previous owner had disconnected the temp horn at the controls...noticed this when installing a new console. Hooked it up and got the following: Started motor and the horn buzzes immediately and stays on. Killed motor and put key in on position and grounded wires leading...
  10. F

    Rebuilt motor will not start

    1979 115 evinrude. I've rebuilt one hole and new rings on the others. Compression is 90 on all 4. Motor will not start. Fuel gets to the carbs and the bowls fill up, but no fuel gets to the spark plugs. Good spark on all 4. I also rebuilt the carbs with all new parts, and made sure jets were...
  11. F

    No spark on #1 and #4 after rebuild

    1979 115hp Evinrude- rebuilt with one new piston. I am not getting spark to #1 and #4, checked with red plug unplugged and jumping starter. Any advice welcome.
  12. F

    Throttle/rpm question

    I have a 1979 115hp Evinrude with no tachometer. What RPM range is possible using the warm up lever?
  13. F

    Gel Seal question

    Do I apply a thin coat to the entire surface of both halves of the crankcase? The manual is somewhat vague. Also, the manual says to stay 1/4 inch away from the labyrinth seals...what are they?
  14. F

    break in help

    I will be rebuilding my 1979 115hp Evinrude this weekend and would like to know what break in I can do in the driveway using muffs, and what else once on the lake. I would like to do as much as possible in my driveway. I have no tach, and no longer have a timing light. (That reminds me...will I...
  15. F

    1979 115 hp evinrude rebuild help

    I took my 1979 115 hp motor apart close to 2 years ago due to losing a ring/piston due to coking. I ordered various parts and due to having 2 kids under the age of 3 have not had time to attempt the rebuild. I will have time over the memorial weekend so I can use all the advice I can get. Here...
  16. F

    Clean powerhead?

    I am in the process of removing the powerhead on my 1979 115 Evinrude for a rebuild. A ring broke due to coking. I am going to rebuild the carbs and replace the thermostats, but was wondering if the block/internals can or should be cleaned...and with what? There is a lot of sticky carbon buildup...
  17. F

    powerhead swap

    I'm having a hard time deciding between a partial rebuild and swapping powerheads since I can't seem to find any that are 1979 or newer (I have a 1979 115hp) Found someone with a 1978 115. I've been told some 1978 115 hp powerheads will bolt on...would a serial number tell? Any other way? Is it...
  18. F

    Which gaskets?

    I'm leaning toward just replacing the one bad piston in my 1979 115 Evinrude... What gaskets are needed? Any other advice welcome as well. The ring went out, will get cylinder bored and replace just the one piston/rings. Was going to replace the powerhead with a used one, but it seems all the...
  19. F

    Shaft lenght

    How do you determine the shaft length of the following motors? 1979 115hp V4 model # 115999r 1977 115hp v4 model # 115793s And when looking for a replacement powerhead for the 1979 model...how do I tell what shaft length motor the powerhead came off of?
  20. F

    lower unit interchangeable?

    I have the option of getting a 1977 v4 115hp Evinrude complete minus the lower unit. I have a complete 1979 v4 115 with a blown ring. Will the lower unit from the 1979 work on the 1977? If it does fit am I taking a big step back going with the 1977 motor?
Top