Search results

  1. J

    lower unit ?

    i have a 1985 merc 150 and the prop shaft can be pulled in and out about a 1/8 to1/4 inch is this normal?
  2. J

    lower unit ?

    i have a 1985 merc v150 and i am need to get seals for the lower unit i also have a 1975 115 inline and the part number for the seal kit is the same for the inline but the lower unit is alot bigger.does the seal kit come with different seals that would work for both or am i going to get the wrok...
  3. J

    gear ratio ?

    does anyone know the gear ratio of a 1975 merc 115 inline.
  4. J

    prop ?

    is there any difference in props that have beveld blades and ones that have a straight end blade?
  5. J

    3 to a 4 blade?

    i have a merc 150hp with a 3blade aluminum prop 23p and found a good deal on a 4 blade ss 24 pitch prop my holeshot is perty good wwith the 23p prop would the 4 blade 24p be to much of a difference?
  6. J

    has anybody drilled out?

    the 2 rectangle slots in the midsection for the exhaust has anybody drilled them out to get better performance?
  7. J

    merch tach settings

    i have a 1985 merc 150hp outboard what should the tach setting be it has a 1p,2p,3p,4p switch on the back of it,thanks
  8. J

    setting up merc

    i bought a 1985 merc 150hp for a 17.5ft bass boat and it has a 23pitch prop on it. the last fin on the foot is about even with the bottom of the boat doesnt turn but 5200rpm a guy at a boat shop said that i should raise the motor 1 more hole and that it should throw a rooster tail about as high...
  9. J

    two stroke oil mix

    i just replaced my inline115 with a 1984 merc 150hp and was wondering what would be the proper mixture of oil with 5galons of gas i have heard 40.1 and 50.1 i mixed it 50.1 and it seems to be fouling my plugs.i dont want togo to lean but but not too much oil niether.
  10. J

    wire harness ?

    i have a 1973 evinrude 50hp i rebuilt the engine and had to remove the wire harness it has a long black maybe a resistor block with 6 places to put wires.does anyone know how the wires go from 1 to 6?
  11. J

    1973 evinrude 50hp

    i have a 50hp evinrude serial 50esl73r the bottom cylinder ha 95lbs of compression and the top has 120lbs the motor does run.is this anything to worry about and if so where can i get piston rings from.i have checked this site and they dont go down to a 1973.also the motor has sat for about a...
  12. J

    no fuel on spark plugs

    i have a 1975 merc 115 and was wondering if you are supposed to have alittle fuel on the spark plugs when you turn the motor off and pull the plugs out mine are completly dry and i dont want to burn the motor up i just rebuilt it.it is also had to start the first time.
  13. J

    mercury 150 jets

    does anyone know where to get a inline 150hp carburetor main jets from.rebuild kits dont come with them?
  14. J

    merc 115 fuel problem

    i just rebuilt my 115 it is a 1975 model the problrm i am having is it isnt getting fuel to the spark plug.it has 130lbs of compression and the carbs are getting fuel i can hold my hand over the carbs and turn the motor over and remove my hand and alot of gas will come out the motor is trimmed...
  15. J

    engine builders

    i had piston failure today so i took the engine apart it is a 1973 115hp inline 6.upon removale i noticed the crank was rusted on the bottom 3 cylinders could the bottom crank seal cause this i didnt find any cracks in the block if not what else could cause this
  16. J

    piston flakes on plugs

    i have a 1973 merc 115 motor has ran fine untill i put seafoam in it.took the boat out ysterday and it lost power ck the plugs and noticed small metal flakes on it changed plugs and it ran fine untill it done it againe same cylinder it has 130lbs of compresion on all cylinders just wondering if...
  17. J

    merc thermostat ?

    i have a 1973 merc 115hp and was wondering if it had a thermostat in it i have the manual but it doesnt show anything on the thermostat.if it has one where would it be located cause i have looked everywhere for it.
  18. J

    cannot get tach to work?

    i have a 1973 merc 115 and the manual and i have checked the wire diagramn and have wired up my tach according to the manual and it wont work.the tach worked with a evinrude does the tach have to be for a merc or could the switchbox be bad?
Top