Recent content by topgun3690

  1. topgun3690

    Milky fuel in carb intake force 85hp

    I have a factory manual.....it talks about break in procedures, but the MasterTech version was the one I used. It was more detailed and thorough than the manual was. The "Technical Help" and "Technical Specifications" sections have a lot of good info in there too......some of it specific to...
  2. topgun3690

    Milky fuel in carb intake force 85hp

    https://maxrules.com/fixbreakin.html Might take a look at this info from MasterTech Marine.....is pretty thorough for breaking in a rebuilt PH.....
  3. topgun3690

    Remove throttle and shift cable from Force 85 hp outboard

    Maybe take on old compact screwdriver and cut the handle down a bit....
  4. topgun3690

    Gun Safe

    Lots of vids on youtube where they attack safes....first thing they do is push it over onto it's back, then use 6 foot pry bars on it. If your safe is properly bolted down, and in a confined area like a closet, or in a corner of a room, they will not be able to do that. Bottom line.....the...
  5. topgun3690

    1984 125 force outboard

    Good eye, TFP.....(y)
  6. topgun3690

    Looking for some help

    Be sure to use a clear filter....helps in diagnosing fuel issues as you can see the fuel flowing. Fram G2 or similar will work.
  7. topgun3690

    1989 4 CYl. trigger old style(prestolite) vs new style(CDI)

    They do have a warranty, but with some restrictions......has to be purchased from "authorized" retailers, and installed by a "professional marine technician". 2 years from purchase date. So without a bona fide receipt from a shop I would not count on them honoring any warranty......you would...
  8. topgun3690

    1995 Force 120 no water pumping through powerhead

    The lack of respect for these old Force/Chrysler engines is actually a good thing IMO......makes it affordable to repair, replace, and maintain. (y)
  9. topgun3690

    This will give you a warm fuzzy - NOT!

    Glad it wasn't Texas....lol.
  10. topgun3690

    Newer to hunting - is there a reference book for questions?

    Legal shotgun; Shotguns not larger than 10-gauge, fired from the shoulder, and incapable of holding more than three shells. Shotguns capable of holding more than three shells must be plugged with a one-piece filler (plug) which cannot be removed without disassembling the gun, so the gun's total...
  11. topgun3690

    Need Air Compressor Help

    It's a good feeling when you fix something that is broke......good job. I had the same unit until a few years ago......was working fine but replaced it as the tank was getting pretty corroded/rusty.....was afraid it was gonna "blow"....lol.
  12. topgun3690

    Milky fuel in carb intake force 85hp

    That would be a 4-step torque procedure....:ROFLMAO:
  13. topgun3690

    Milky fuel in carb intake force 85hp

    Yes, there is both a torque spec and sequence for the cylinder head bolts....no sealers are used on the head gasket, put it on dry. If you don't have a factory manual here is the info from Mastertech Marine.....they have a lot of good information on their site.....torque spec for cylinder head...
  14. topgun3690

    fuel hose question

    The Chrysler/Force style fuel fittings are still available if you ever need them.....
  15. topgun3690

    Chrysler 75hp, need direction.

    The air box has a hose that runs to the bottom of the intake behind the bottom carb......some fuel gets spit out the front of the carbs during operation, runs down to the bottom of the air box and is routed to the intake by that hose to be run through again......
See more
Top