I live on Coinjock Bay, just off Currituck Sound in NC. Had my boat over for about 3 or 4 mos and now I
have barnacles on the bottom. It is a fiberglass boat, so what is the best method to remove them
without scratching the bottom...
I have a 1999 Sprint bass boat that has developed a few elect. problems.
About 3 months ago my aerator pump which pumps water into the live wells
quit working. I removed the pump and checked it, was bad. So I replaced
the pump, but when I tried it with the switch- nothing. I can run a hot...
I am new to the Yamaha forum. Over the years I have had several Merc
outboards- 90hp merc in line 6, 50hp blue stripe, and a merc 90hp 3cyl- but
I have just purchased my first Yamaha. It is a 1999 C150TLRX on a 1999
Sprint 280pro. When I was going to replace my plugs on the 50 and 90hp
Mercs...
I am looking at buying a 1999 Stratos (per seller) and the photo shows to
be a 286 pro, but I cannot find any info on a 286 pro. Nada shows a
285 but not a 286. Does anyone know where I can find any info on a 286
pro?
Thanks...
Motor--1987 merc 90hp 3cyl. serial #b153941...
On Saturday I was idling along after running around for about 2 hrs and all
of a sudden -thunk- engine quits. I dont mean slows down to a stop I mean
complete stop.. When I tried to start -thunk- no turn of motor. I was towed
in and pulled the...
Trying to help a neighbor. He just bought a used (1998?) mercury 200hp
outboard. He needs a new impeller. While trying to look up the impeller
on line the serial # doesn't seem to match up. His motor says 200efi xl but
on one website his serial # (0G654635) shows to be a 200dfi? Does this...
installing new motor on boat. Motor was always in forward gear. Pulled lower
unit and turned shaft. I could get the lower unit to shift to neutral. My
queston is when the shifter is in foward the prop should lock in whitch direction. I now have the lower unit in neutral (?)--free wheels in...
I purchased a used (1989 by owner) merc 3cyl 90hp motor. Cannot find an
external serial # plate but found a small plug on the right hand side of motor
that is stamped with b153941, is this the serial # and if correct is the year
right. Also I want to check the tilt operation before I install on...
Last weekend I purchased a 1989 (per customer) 90hp 3cyl mercury outboard.
Due to weather and work it is still laying in the bed of my truck. I was
checking all the connectors for compatibility with my old 50hp merc and I tried
to make sure it would shift. the prop free wheels in one direction...
This weekend I am buying a used 1989 Merc 90hp. This motor has been
sitting up for about one year (was serviced at local bass pro shop last Nov.)
Is there anything I should check or do before starting or using this motor.
New impeller? Decarbon? Clean carb bowls, etc...
I have a 1983 merc 50hp 4cyl motor and the upper 2 cylinders are not getting
fuel. It happened before and I could remove and clean the carb, then the
problem would go away for a few days. Now I have rebuilt the upper carb
again and tried a different carb from a spare engine and still have the...
I have a 1983 Merc 50hp 4cyl. On the left side of the engine there is a
semi transpartent bowl that you can see the fuel in. (fuel filter?) Does it
just spin on (threaded) or what else. I have tried to turn it off but it gets
real hard to turn and I don't want to break it.
I keep having...
service manual says to hold carb upside down and adjust needle actuating
lever to have the bottom of the float at 1/4" from carb body bowl ring, no
problem. but then it says to turn carb over and adjust the drop of the
float where it is 1/64" from bottom of float to top of the main fuel jet...
1985 Merc 50hp. Water pump quit pumping while running.(see Lower Post)
I found the impeller seperated from inner brass sleeve. Replaced impeller
and gasket. Replaced lower unit, motor seems to start fine but no water
from pee hole. Removed lower unit and shot compressed air back thru
pee...