Search results

  1. J

    Trolling Motor Outlet and Plug

    I have a problem with my trolling motor, and I am hoping it is the plug or outlet. It was previously working. I started checking the voltage at the plug, and have 27 v, but I think it is in the wrong location. It does not match the plug wiring. Can the outlet go bad I attached a couple pics...
  2. J

    Do your locker locks have matching keys?

    I bought a 1998 Alumacraft Trophy last year, and all of the lockers have locks on them. I have a key that fits them, but I can't lock or unlock them. I was going to pull one and take it to a locksmith to have keys made. Would all of the lockers have matching keys? Should I just take all of...
  3. J

    New prop doesn't clear Trim Tab

    Here's what I have. 1998 Mariner 135 hp Optimax motor. Current prop, is original aluminum Black max 48-832830-c1-19. I went through Mercury prop selector and came up with Mercury Tempest Plus 48-825862-21p based on what I entered. I put on the prop and it doesn't clear my trim tab. Is there...
  4. J

    Replacing well used prop

    Here is what I have. Alumacraft Trophy 185 with a 1998 Mariner Optimax 135 hp. I am running an alumimum Black Max 14.5 x19 prop. Hole shot is great and I run about 41-42 mph at 5600 WOT with 2 or 3 in the boat. (I think WOT on this motor should be 5000-5600) The original prop has seen better...
  5. J

    Lowrance Transducer, Humminbird Unit

    I bought a nice used trolling motor, but the guy I bought it from ran the transducer cable up through the shaft. Problem is that it is a lowrance skimmer transducer, and was hooked to a Lowrance X50 unit that I do not want to use. I have a Humminbird 747c that I have been using, and would like...
  6. J

    Mercury 70 hp Tilt/Trim Rebuild

    I have a 1989 Mercury 70 hp with tilt and trim that leaks down. The s/n is OC137125. How do I rebuild the trim? How do I find the parts?
  7. J

    70 hp Merc Vibration

    I have '89 Mercury 70 hp motor that I bumped a stump with at 5 mph last fall and bent up my aluminum prop. Put a new prop on it and took it back out. I notice a very slight vibration at low idle when in gear. Go any faster and it goes away. I have really looked at the prop shaft, and I don't...
  8. J

    Prop Suggestion

    I have yet another prop question. Here's what I am working with. Had a Michigan wheel 12 3/4" x 21p aluminum prop on a 1989 70hp mercury with t/t. That is on a 16' sylvan aluminum deep-v boat with console. Bumped a submerged stump just at low speed(5-6mph). Broke the prop. The boat had ok...
  9. J

    1989 70 hp Tilt Trim repair

    I am having problems with my tilt and trim leaking down. It does this even while operating the boat. It works well up and down, just cannot hold it's position for very long. What could be causing this? Can this be repaired?
  10. J

    115 Lower unit Bearing

    I have a 1985 115 hp Merc inline 6. I took the lower unit off the other day to put in a new water pump. While doing this I noticed that with the water pump off the drive shaft had some play in it. Is this normal? Should I replace the top bearing that I could see with the water pump off...
  11. J

    9.9 Tohatsu Wiring

    I have what I believe is an '85 Tohatsu 9.9 hp motor. M9.9B 355A 98187. It has 4 wires that are not connected that should go to controls. There is a white, black, and the other two might be brown and tan. How would I connect these to controls?
  12. J

    Tire wear

    I have a Yacht Club single axle trailer that I haul a 16 foot aluminum boat with a full interior and 70 hp merc. I am having a problem with the tires wearing on the inside of each of the tires. The axle seems to be straight with the trailer and it trails ok. Could it be possible that my axle...
  13. J

    Raising Motor Position

    I have 70 hp Mercury on v bottom aluminum boat. With my current setup the engine creates a bunch of drag because the AV plate is 1" below the hull line. The holes are about 3/4" raise each, so I am thinking 2 holes higher. I don't have a hoist to lift the motor. I do have other tools and a...
  14. J

    Mariner 40 HP Lower unit

    Is there a place where I can cross reference what lower units will fit my 1986 40 hp Mariner? Need to replace mine, I am sure they put that one more than one motor.
  15. J

    89 70 hp Merc Charging System

    Would a 89 70 hp Merc. have a standard battery charging system? The reason I ask is a bought a 75 hp motor as a parts motor and there seems to be another electrical part mounted that I don't have on my 70.
  16. J

    Kicker Motor Size

    I have 89 Sylvan Deep V aluminum boat with a 70hp merc, and just can't get it to go slow enough for some of the trolling I wan to do. Any suggestions on kicker motor size for this boat? It has full interior, and live well, so it isn't a light aluminum boat. Also do those trolling plates you...
  17. J

    Intermitent Power Loss

    I have a 1989 70 hp Merc that loses power randomly at WOT. Sometimes it runs great, then the next time it will open up for a while then slows to 2500-3000 rpm. If I push the choke she speeds back up. Ran a can of Power tune through it and same thing. New fuel lines and fuel filter. Any...
  18. J

    Pinion Gear chip

    I have a 89 70hp merc that I took in to get the lower unit sealed. Upon disassembly they found a small chip on the pinion gear. Says it looks like it has been there a while. Do I need to replace it? What's the chances of something going wrong if he just puts it back together?
  19. J

    Cracked Screen Humminbird

    Has anyone ever tried to replace a cracked outer display on a humminbird? Humminbird will do it for $250 on my Matrix 97, should never crack for $250. I took it apart, just looks like plexiglass. Any tips, suggestions.
  20. J

    70hp 1989 tilt trim

    I put a new tilt trim motor and selenoids and bled it out and worked fine. Now only works well going up on the 2 trim cylinders, will not go down. Really slow up or down on the single trailer cylinder. Is the motor bad?
Top