Search results

  1. D

    143 or 105 Vernatherm for 60HP VRO

    I would like to change the vernatherm on my 60HP Evinrude VRO E60TLESM from 1990.<br />Whitch type of vernatherm shall I order<br />OMC-394411 ( 143F )<br />or<br />OMC-384719 ( 105F )<br /><br />Regards DUKE 3
  2. D

    Cooling water temp.

    I have installed a temp. gauge at my Evinrude 60HP, VRO from 1990. So I can read what the temp. is.<br />But what is normal operation temp. I should read at my temp. gauge ?<br />And what is normal open/close temp. the thermostat is working at ?
  3. D

    High voltage

    What sollusion shall I take ?<br />My 60HP Evinrude from 1990 gives me from 13,5V DC - 18,9V DC to my batteries.<br />The rectifier is OK, the batteries are OK, all cables and grounds are tight. (last month my fishfinder stopped working, maby becose of the high voltage ? )<br /><br />So what...
  4. D

    BAD TACH, RECTIFIER OR BATTERY ??

    My motor is an evinrude 60HP VRO from 1990, and it is running 100% OK.<br />The tach is from a Mercury outboard motor, and on the backside of the tach, are there standing<br />1. 4 cyl<br />2. 6 cyl<br />3. 8 cyl<br />4. 12 pole (this pos. is where I put it)<br /><br />The tack have no name, and...
  5. D

    Tachometer

    Hello.<br />Last week I have installed a tach (0-6000rpm) from an 6 years old 4 cyl. Mercury on my 60HP Evinrude VRO from 1990.<br />The tach can be adjusted from 2 to 8 pol.<br />So since my Evinrude is 3 cyl. 2-stroke, I did adjust the tach to 6 pol.<br />So when I start up the motor, the tach...
  6. D

    Evinrude 60HP VRO 1990 temp.

    Hello out there.<br />I have a small question.<br />Is the cooling water temp. around the temp.switch, the same as the cooling water there is comming out of the pea-hole.<br />The servicebulletin according to outlet of cooling-water to the pea-hole from the top of the motor, hase been done.
  7. D

    Evinrude 60 HP VRO, 1990, max 2500 rpm ?

    I have cleaned and adjusted carbs, performed ”link n sync”, adjusted ignition with a timeing light at the flyweel, installed new QL77JC4 plugs, new gazolin, new fuelhoses and handpump, new VRO-oilhose and handpump, new power pack, new alarmsystem (horn, wirers and alarm-lamp.)<br />But when we...
  8. D

    Warning horn Evinrude 60 HP VRO 1990

    Hello out there.<br /><br />My warning horn (3 wirer model) on my Evinrude 1990 60HP VRO does not work. I have tryid to ground the TAN wirer at the temp.switch, but still no sound from the warning horn.<br />My qustion is, can I use any 12V, 2 wirer warning horn to replace my 3 wirer model ?<br...
  9. D

    S.L.O.W.

    Hello out there.<br />I just have a small qustion, from my Evinrude 60 HP VRO from 1990.<br />Is it only high temp. there can activate the s.l.o.w. funktion in the power pack ? Or can too high rpm also do it ?
  10. D

    Evinrude 60 HP idle speed

    I can find a lot of members here, there have/had the same problem as mine.<br />The Evenrude 60 HP VRO from 1990 wont idle, when I put in water, becose of the back-pressure on the exhauste.<br />I have cleaned the carburators, new plugs, clean tank, new gas, new hoses and handpumps, there is no...
  11. D

    60 HP Evinrude VRO ( alarm )

    Hello out there.<br />My alarm system on my Evinrude 60HP VRO from 1990 is not working.<br />The purple wirer from the remote control, is not connected any where in the motor. But the purple wirer from the VRO-pump hase the owner of the motor before me, placed at the primer solenoid valve...
  12. D

    Idle speed

    Hello<br /><br />Im from Denmark, and Im trying through this page, to find some one, who can help me, about some problems with my Evinrude 60Hp VRO from 1990.<br />I did bye this motor (and boat) last year. And my first trip with this motor was very very bad.<br />After few min. it start to run...
Top