Search results

  1. S

    48 special tilt assist won't go all the way down

    The cable broke so I let the pressure out of the set screw to get the motor down. I’m fine with leaving the cable broken but the engine does not go all the way down. Under throttle it will force it’s way down but then it bounces back up or trims up a couple of inches. Is there a proper way to...
  2. S

    Torsion axle life expectancy.

    How long does a torsion axle last before the rubber breaks down and the axle is junk? I’m looking at a 10 year old 7,000 pound trailer with tandem axles. California fresh water trailer loaded right and taken care of by a buddy. It is priced right but not if I will need to buy two fresh axles...
  3. S

    Narrowing a trailer frame

    I needed a narrow trailer for a long skinny Grumman Sportboat. The frame I had was just way to wide so the easiest thing to do was grind off the mounts on the axle frame and relocate them in. The frame did not bend easy. It took three ratchet straps for safty and I had to pull the rails until...
  4. S

    Tieing knot to EXACT length

    I need a knot for an exact length when loaded to within 1/4-1/2” without the bulk of truckers hitch. I don't want to go with a turn buckle and associated hardware. Imagine hanging an anchor from a celing beam 1\4” off the floor with clean looking rigging. Is there a knot that I could use to dial...
  5. S

    How to survive falling in the ocean for 10 hours

    I'll just leave the coments to you but whatever she did it worked. http://www.foxnews.com/travel/2018/08/20/british-woman-who-fell-off-ship-in-croatia-credits-singing-and-yoga-for-surviving-10-hour-ordeal.html
  6. S

    Blue sky (up) Green Grass (down) trim pump

    I watched a guy pull his Sea Ray out last evening and drag the outdrive on the ramp. As I was loading my boat I noticed they were still at the waters edge so I asked if they needed help. "I just bought it and the drive won't go up". It's getting dark. I thought it may just be bound on the...
  7. S

    Calculating thrust

    I'm trying to fiqure out what size fan would be best. I'm looking at this one at lowes but don't know how to convert CFM to thrust...
  8. S

    Avon Redseal hypalon boat refirb

    I found a home for the 4 horse folding outboard that I refirbished. I left it ugly as a theft deterrent but it runs like a top.
  9. S

    Tire sidewall repair

    I fixed a nasty 3" rip in a sidewall. I sewed it up with waxed nylon cord. ​ A patch was installed inside for good measure. ​​​​​​​ ​​​​​​​ Shoo goo got smeared over the outside threads. What do you think? Good as new?
  10. S

    Subscribe and unsubscribe

    Subscribing to threads is as easy as hitting the subscribe tab at the top of a thread. Now you will get updates in you inbox and can check the threads you found of interest. Just as nice is you can unsubscribe when you are done or bored with a topic. One I got rid of was "what do you pull your...
  11. S

    1976 Evinrude 15HP Dies.

    Gents, I'm resurrecting a 15604R 1976 Evinrude 15hp that sat for 9 years. I replaced the starter rope, water pump, upper ignition coil and cleaned the carb. It starts, runs and idles great but after 2 minuets it dies. Bulb stays hard and pumping makes no difference. It starts right back up and...
  12. S

    Cleaning metal outboard tanks

    I've got a Merc tank and two OMC metal tanks from the 80's that were full of old rotten gasolene. Luckily little to no rust because of the desert. They have that brown goo from ethanol and they need a good washing of the inside. Any recomendations as far as soap goes? I'd like to use water and...
  13. S

    Am I being a Richard Cranium?

    Lake Pleasant AZ is the big lake near Phoenix. It has one stretch at the mouth clearly marked No Skiing. It's so nice to get away from the surf boats doing circles and the canyon walls block some wind and provide shade. You see party barges enjoying the peace or old school jet boats wanting to...
  14. S

    Smaller or larger diameter prop **Results Added**

    I've narrowed my prop choice down to two based on availability. They are both OEM props. One is a stainless 11 1/4" X 19 pitch and the other an aluminum 12" x 17 pitch. I'm leaning toward the smaller diameter higher pitch but never experianced a diameter change before. What's effect does...
  15. S

    Additional sound deadening material inside the cowl.

    My factory cowl foam looks mint. 1991 Evinrude 48spl 2cly 2 stroke. Will ripping it out and replacing it with one of the newer style insulating pads like dynamat help reduce sound much? My cruise RPM is 4500 and after an hour I get tired of the noise and having to yell over it. I know it won't...
  16. S

    Power Ranger Action figures invade the lake!

    Little kid on the boat wanted to go back to the cove with the Power Rangers. I said "No Jonny they are fisherman dressed up like Power Rangers and they are busy saving the lake." I have to admit they look like odd standing on those sticker covered bass boats with NASCAR uniforms on. Best I...
  17. S

    Thru hull fuel vent for smaller hose

    I'm adding a built in 15 gallon aluminum tank to replace a 6 gallon portable tank. The only thru hull vents I find take a whopping 5/8" hose. I like to use a 3/8" hose because the volume and consumption rate are very low. Any suggestions or do you know where I can find a thru hull that's smaller...
  18. S

    Bass boat racing

    How come bass tounaments do not have to go by the rules and get the permits other racing sanctions do? http://www.click2houston.com/news/father-killed-wife-and-daughter-injured-after-boat-crash-on-lake-conroe
  19. S

    Loosening Up No Feedback Steering.

    I installed a 3:1 NFB helm with a new cable on a lite aluminum boat with a lite 48hp motor and want to loosen it up. Specifically the sticktion in the wheel is hard to overcome. Can it be greased or adjusted to free it up a little?
  20. S

    2 hp refirbishing for "Tactical Pac" for lack of better description

    J2RCSM 1980 Johnson 2 hp. I bought this as a running back up motor to get me out of a bind and for future use on a yacht tender dingy. I'd like to eventually find a case or build a box so it's all self contained with spare parts and two quarts of premixed fuel in metal cans. A grab and go kinda...
Top