Search results

  1. S

    Mariner 60 1998 weak spark No2

    Hi All<br />I have a mariner 60 serial No op004089, giving me a hard time. it starts fine but runs like a bag of spanners,if i pull the HT lead off No 2 It does little to the running of the engine ,if i pull 1or2 HT off it boggs down.So have borrowed a known good stator and trigger and replaced...
  2. S

    Johnson 60 Over charging?

    Hi All <br /> I have a Johnson 60 over chaging it seems 17v at idle, can anyone help me on this ,have changed the rectifier no change.
  3. S

    Force 120 clicks in neutral

    Sorry to duplicate but the other post is closed . I have a force 120 that click when i spin the prop in neutral ,ca someone tell me what this is doing to th gears or dog clutch and will it damage anything ,and if i need to remove lower leg what must i do to make sure it does not go back the came...
  4. S

    CRYSLER 75 SMOKING

    Hi <br />I have a cyrsler 75 1980 model, it smokes to much at idle and with a bit of revs as well.i can lean out the carbs till it pops and still smokes,have measured and remeasured oil to fuel 50/1 and still the same<br />Any help welcomed
  5. S

    Johnson 60 missing ?

    Hi .<br />I have a Johnson 60 that runs ok ,starts esay etc.BUT when it is at idle and but not as bad when you rev it up slowly ,it seems to miss a beat every so often. When it idles it will kick the engine sideways in a jerking movement when it misses or what ever it is doing any thoughts on...
  6. S

    Mariner 20 Won't accelerate

    Hi all .<br />I have a Mariner 20 that starts and will idle ,but with a little vibration.it will engage into gear at low rev's but as soon as i accelerate to go it will start to rev then cut out.It seems that it is only under load ,because when it is in neutral and i rev it at the carb it will rev??
  7. S

    Alpha one Prop Number Identify

    Hi all<br />I have a prop No that i would like to find out what size etc, 46- 16438A45-14P<br />All help appreciated<br />Thanx
  8. S

    9.9 Johnson 4 Stroke Won't Rev

    9.9 Johnson 4 Stroke Won't Rev Hi Fellow boaters<br />I have a 2002 9.9 4 stroke which will idle ok but when i try to rev it it revs up a bit but sounds like it is labouring as well as vibrating.<br />have checked plug gap and set it to 0.8 mm.Removed carb and given it a good clean it needed...
  9. S

    Mercury 100 Back fire

    Hi I have a Merc 100 ,it does not have clean rev up if you move the throttle linkage up on the carbs,it seem to hesitate and pop out the exhasts,it also tries to push presure back to the fuel pump down the pipe which goes into the cranck case when it is doing this back firring,i have just...
  10. S

    Mariner 55 year??

    Hi i am looking to fined out the year of my 55 Hp with Serial No 319630,
  11. S

    No reverse in water

    Hi all<br />I am having a problem with my evinrude 50 ,with the muffs on on the drive it engages in gears no problem ,put it in the water and no reverse it just grindes and the controls bounce up and down slightly
  12. S

    Mariner 60 lumpy at start up

    Hi <br />I have a Mariner 60 and at first when i start it seems to run on 2 cylinders but after 5 mins like that it seems to clear then runs fine for the day,starts all over again the next day ,<br />Any help welcomed<br />Thanx
  13. S

    IGNITION WIRING CRYSLER 75

    Hi all, I would like to know where the purple wire in my wiring loom goes on the ignition switch ,i have a push in for choke switch,and if i conect it to one of the M positions and measure between the 2 M positions i get a reading of 15v but across my battery terminals i only have 11.5 v.Where...
  14. S

    Ingnition Wirring

    I have a Crysler 75 ,1980 Skier.I have conected a Evinrude ignition switch to it and not sure where 2 wires go ,the purple and black .these are ment to go to the 2 positions M, does it matter which way,if i conect them and run the engine at the switch i get 15v but it is not charging my Battery?
Top