Search results

  1. Blazinmonkey

    Quick TEMP question on a 2000 johnson 150

    Hello- I have a new to me 2000 150. Runs good, everything looks to be working with the 4 light tach gauge and alarm. I took an old temp gauge from a 140 evinrude. the gauge shows that the TEMP. goes up the faster I go. When I slow back to idle the temp goes back down. My question is that...
  2. Blazinmonkey

    Hey everyone, got a question about Timing... 140 looper

    1985 140 looper J140TLCOS Hey everyone, got a question about Timing. I am missing the sticker on the air box for the timing degree number. The motor is a 1985 but check the part numbers on the ignition components they are for a 1986 -1987 model. I have read it is from 19 deg. to 22deg...
  3. Blazinmonkey

    1985 140 melted statorl

    the first sign was the tachometer stopped working a few years ago. used/ran the motor all season - runs great, starts right up, idles nice, no cough or sneeze. just a slight stumble at full throttle. never a problem charging the battery. then after a long day idling the motor started to lose...
  4. Blazinmonkey

    1987 Evinrude 150 Unburnt oil running down midsection

    Re: 1987 Evinrude 150 Unburnt oil running down midsection I attached pics of my 1983 150 cross-flow... you can see oil down the midsection & prop. this mainly happens when i flush the motor on the `ear muffs' I boat in salt water so when I get home I idle with water then salt away. after a few...
  5. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns so I took 15 min to layout the screw locations 2" from the edge every 4" then 6" on the inside... the one picture shows why you should pre-drill... I hope to glue in the morning... mark & trim the top after the glue tries... thank you again for the...
  6. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns I went to my local lumber yard bought 2 sheets of 3/4 AC plywood or G1 ext. as they called it The pic of the wood with out the clamps is the first ply alone... with the clamps both pieces together... how close should the would be to the skin on the...
  7. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns ok all the old wood is out...
  8. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns you think I could pour some glue or thin some epoxy to pour in?
  9. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns I want to thank every one for their input. I see what every one was telling me about the cut location...
  10. Blazinmonkey

    Splash well removal 1985 4 winns

    Re: Splash well removal 1985 4 winns I can not thank every one enough for their replies... so glad I posted on iboats before cutting... the end of the tape is a transition... so my best bet is to cut around 15-16 inches? middle of teak aft screws? thank you for your input...
  11. Blazinmonkey

    Splash well removal 1985 4 winns

    Hello dry dock... I am going to remove my splash well to access the transom wood. In the first picture I made a light pencil/cut line to cut the cap. That line is my best guess of where to cut the cap. Considering this site is where I get/will get the bulk of my information, I thought it...
  12. Blazinmonkey

    gas octane ratinig 88 sticker on my 1985 140 looper...

    sorry if this is a dumb question. I would think no but I am not positive... so my 1985 j140tlcos has a octane ratinig of 88 sticker on it... is 87 octane ok to use? or will i notice a decrease in performance? motor idles with out a cough or a sneeze on 87... smooth for a looper... thank you...
  13. Blazinmonkey

    tach compatibility 1985 140

    1985 140 (j140tlcos) tach compatibility I believe the ignition is from an 1984. I say this because when I replaced the power pack the 1985 power pack was a little different but the 1984 power pack was an exact match of the old one. I am going to replace my tach & wanted to know if the...
  14. Blazinmonkey

    Replacing vro oil line with automotive 1/4 fuel line 1985 j140

    hi, I have a 1985 J140 TLCO can 1/4 I.D. auto store fuel line be used to replace my VRO oil line from primer bulb to front of motor? or do i need a special oil line from a dealer? also... please see link...
  15. Blazinmonkey

    1985 140 VRO vacuum line HELP

    i was hoping some one here could answer my questions on vacuum lines. would a small vacuum line CRACK cause my 1985 140 johnson run out of fuel and stall, but idle fine? also i broke the vacuum line T with an arrow on it behind the VRO where could i get a replacement? thanks for any input...
Top