Search results

  1. ben2go

    Recommend engine brackets

    I am looking to install two outboard brackets. Universal units will be fine. I would like one for a 25 to 30HP remote operated OB and one for a 9.9HP kicker. I don't need any special features for the main engine. Fixed open bracket will be fine. I would like the kicker bracket to be adjustable...
  2. ben2go

    Alpha 1 Gen 2-What to do with exhaust and water cooling intakes?

    I am planning a diesel conversion on an Alpha 1 Gen 2 stern drive.I am using close loop cooling on the engine and thru hull exhaust at the water line.What do I do about the exhaust port thru the drive,and what do I do about the water intake?Can I block off the exhaust by welding a bung in?Can I...
  3. ben2go

    Alpha I Auto Trim,who has it and is it worth it.

    I am looking at options for an Alpha I I/O for the boat I am planning to build.One of the options I was given was auto trim.Is it worth it and does it keep the boat trimmed properly?I have only used manual trim at the controls.I am installing an auto pilot.Will auto trim be a good option to...
  4. ben2go

    Cavitation plate question

    I have a 1980 Tecumseh 5hp Gamefisher with a broken cavitation plate.The boat I am planning to use this motor on is not designed to plane.So the lower unit will remain submerged.The cavitation plate doesn't help with water flow into the water pump intake.Can I just cut off the rest of the...
  5. ben2go

    5 HP Gamefisher Carb Ignition Sync

    1980 Eska built 5 HP Gamefisher Model# 217-585460 Tecumseh air cooled 1 cylinder power head. I have fuel and bright blue spark,but my engine just pops through the exhaust column.When I changed the points and condenser,I set the points per service manual.I couldn't check the carb ignition...
  6. ben2go

    Minn Kota Trolling Motor Question

    I have a 1990/91 3HP Minn Kota trolling motor.The prop pin has rusted into the prop shaft.I let it set and used pentrating oil everyday for 2 months.I have tried squeezing it out with channel lock pliers,pressing it out with a C clamp,and hammering it out.No dice.I also have 2 wire ends in the...
  7. ben2go

    5HP Gamefisher Question

    I have a 1980 5HP Sears Gamefisher outboard model 217-585460.I need to find info on the fuel hose routing and on/off valve.This motor has an on board tank as well as a connection for an external tank.When the motor was given to me,I knew the fuel hose routing was wrong.Should the fuel valve turn...
  8. ben2go

    3HP Minn Kota trolling motor prop removal help

    I have a 3HP Minn Kota trolling motor and I can not get the prop off.I removed the center nut and tried to pull it off.Even tried unscrewing it with no luck.I have it setting over night coated in penatrating oil.I tried tapping the prop shaft and that didn't help either.I need to get this thing...
  9. ben2go

    Need Help Identifing The Maker Of My Jon Boat

    Here's what I know.The boat is 10 foot long,max depth of hull is 12 inches,beam is 36 inches,riveted hull,stiffeners on the floor only,seat pods have close cell foam in them,and a wood reinforced transom.My hull identification plate has faded out and the serial numbers weren't engraved/stamped...
  10. ben2go

    What Outboard and Rigging Fits My Needs?

    I am building a very unique boat that I designed my self.It is a flat bottom cabin cruiser with a bow like the old WWII landing crafts.The boat has a 30 foot hull length,27.5 foot water line.It's non planing and will be used in shallow lakes and rivers.No rough water or salt water.Estimated dry...
Top