Search results

  1. B

    1958 7.5 ad-12 carb settings

    How many turns out should I be with the top carb adj. and bottom carb adj. Thanks
  2. B

    Getting shocked when I touch the outside of my yamaha

    I have a 1992 130 yamaha. It runs great. I noticed when I put the boat on the trailer and walked around the back I touched by the exhaust at midsection. I got shocked. I started touching all the outside of the motor and was getting shocked. Any suggestions. Thanks
  3. B

    1958 johson 7.5 hp

    What should my 2 stroke oil be 25 to 1 , 50 to1.?
  4. B

    Spark plug not firing after engine is warm

    My 95 6 cyl 150 intruder will run for an hour and then when I check the #4 plug it does not fire. I bought a new dual coil thinking that was the problem and the same results. After a while the same plug that was firing is not firing. Great compression and getting fuel.
  5. B

    corroded steering bracket on 92 130 Yamaha

    How tough is it to replace my steering bracket if I pull my powerhead?
  6. B

    97 1902 trophy center console hatch

    What is that hatch used for under the console. It is hard to reach in there?
  7. B

    I need to contact Rodbolt

    How can I contact him?Doen anyone have his phone #?
  8. B

    92 130 Yamaha block corroded

    I have two questions. Can I take my 92 130 pistons and put them in a newer block from the mid to late ninties and put that powerhead on my 1992 130 from exhaust down? Does anyone have a clean block for sale?
  9. B

    Water in #2 cylinder

    My 92 130 Yamaha ran great today until heading back to the boat ramp it did not sound right . I did not have full power to load the boat on the trailer. I checked spark, compression 130 on all 4 cyl. When I looked at the #2 plug then I had seen that it was milky. I went home and had extra head...
  10. B

    Still have shavings on Yamaha magnet screw

    I had the gears go bad in my lower unit on my 130 last month.The dealer said he shimmed the new ones. Last week after running it for two hours I checked The magnet screw and found some shavings. No metal chunks like before itwas bad. I took the boat out today and ran for three hours. I checked...
  11. B

    My Crankshaft is chipped in a few spot on my 60 degreee 150 intruder

    I am rebuilding this engine and noticed where the sleeve meets below the main lower bearing there is a clip that is removable. Right next to that is a round almost like washer that is part of the crankshaft. This will spin when the engine is running. It sits on top of the seal. I think it will...
  12. B

    joining yamaha crankase halves together

    What is better. Yammabond 4 or yammabond 5? Thanks
  13. B

    Yammabond #4 or #5 on crankcase

    Putting a block back together. What is better of the two Yammabond #4 or Yammabond #5? Thanks I do not care for OMC gel Seal.
  14. B

    Yamaha v-4 prop torque at ?

    How many foot lbs do I torque my 130 Yamaha v-4 prop? 40, 45 ,50 ft lbs?
  15. B

    U bolts torqued at ?

    What should I torque the ubolts that support the wood on the trailer to support the Hull? 50 FT lbs. 75 lbs? Thanks
  16. B

    gear lube leaking around my shifter on lower unit

    I was putting a new waterpump on my 92 130 yamaha and noticed oil leaking around the shifter. It is held in by three bolts. Do I need any special tools. It looks like it would just pop up and put some type of oring around it. Any suggestions would be helpful. Thanks
  17. B

    130 Yamaha overheated

    My 1993 yamaha 130 overheated today. I was running at trolling speed for 7 minutes and wide open for one minute when all of a sudden it lost power and shook violently. I notice no water was peeing out. It took me two minutes to idle to shore and then I put it up on the trailer. I pulled the...
  18. B

    Replace my single axle trailer with tandem?

    Will it be alot easier tow for my truck going from single axle to double for my 19 foot boat? Will it also be easier on my transmission? Thanks
  19. B

    97 225 carberated mercury poppet valve

    Where would the poppet valve be located on this engine?
  20. B

    Swap lower unit on my 150 evinrude

    If I take my lower off my 110 johnson and stick it on my 95 60 degree 150 intruder would this create any problems since the splines line up? Thanks My intruder lower is bad.
Top