Search results

  1. grizzreaper

    thru hull gas line fitting

    not sure where to post this ? on. but want to run my gas line thru my transom. I have a inboard/outboard with a 15 hp outboard. I want to secure the outboards gas tank in the dog house. this way its a nice even flow with no kinks or bends. is there such a fitting if so what is it called. the...
  2. grizzreaper

    Three battery on a two way switch

    Tried searching but I didn't see anything. I want to put three batteries in the boat. Two cranking and one deep cycle. On the switch it will be one for the cranks and two for the deep (house). Is it better to hook the cranking in series or parallel. The motor is a 1985 3.0 mercrusier. The...
  3. grizzreaper

    Killswitch

    I been trying to figure out how to wire my kill switch. There is two wires black with yellow stripe.i put a new throttle shifter in and it's a 3000 for a mercrusier. Not sure what wire goes where on the key switch. Original shifter did not have the lanyard key/ Killswitch. Thanks in advance...
  4. grizzreaper

    1984 4 hp evinrude

    I just redone the carb on this. Going to change the plugs now. Fuel mix is 50:1. It took a bit to get motor running. I seated the slow speed needle valve in. Then backed it off 1 n half turns. Idled rough. Stalls out on . Not sure what the problem is. If I keep the motor wide open she runs...
  5. grizzreaper

    1986 221 StarCraft islander

    1986 Starcraft Islander 221 Transom is rotten about a quarter of the way up.. so I can a patch this with replacement wood and fiberglass in. Or do I have to pull it all off. if I have to pull it all off, is there a way to remove the rear rub rails and top plate so I can pull the transom out. I...
  6. grizzreaper

    What year

    Hello I have a 4 hp Evinrude. Model # E4BRCRM. Serial C7188895. Which I believe is a 82 but I can not find any info on it. I need a prop for it. Thanks in advance.
  7. grizzreaper

    I am a smuck - 9.9 Lower Unit Problems

    This spring I took the bottom end off this motor. Put in reverse n could not get apart. With some tugging I ended up removing the shift lever. Then lost lever n pin. Found new locking pin n lever. After putting together I get forward, neutral but no reverse. Take back apart I push linkage down I...
  8. grizzreaper

    Coupler,flywheel and rear motor mount

    Silly question here. Before I go any further, do I have to change my flywheel, coupler and rear motor mount. I removed a 1986 3.0 mercursier 140 hp and I am putting a 1984 3.0 mercursier 140 hp. I have read 1992 n under I do not. Is this correct
  9. grizzreaper

    3.0 mercruiser key switch

    Good morning to everyone. So far so good on the donor motor. I have put my wiring harness on, it's all wired n ready to go. This motor came with a backyard key switch. I thought the switch was bad. So I wired in a new switch. If I jump the starter she cranks and fires right up. I turn the ign...
  10. grizzreaper

    1984 3.0 mercrusier

    Can someone on here tell me where I can get the diagram for the shifter controls. On the carb someone has removed the hookup. I have it just don't have a clue on how to hook it up on the carb or throttle control. Thanks in advance. Will add pictures if needed when I get home from work
  11. grizzreaper

    Alternator

    I have a 1984 3.0 140 HP mercrusier . it can with no alternator or starter. Starter I hooked a old one I had with no issues. I have two mercury marine and a Wilson which I think is a automotive one. First picture has two post and three black wires.two wires on one post and a single on a smaller...
  12. grizzreaper

    Gimbal bearing Alpha 1

    I am going to install the new gimbal bearing. Some sites are saying to install the stamp dot to the top facing towards out drive with the two I assume are grease slots towards motor. Others are saying grease hole on bottom toward grease nipple. I assume it would be dot to top. It's a 86 3.0...
  13. grizzreaper

    86 Alpha 1 out drive

    Hello everyone I just put a new impeller kit on the outdrive. Getting ready to install bellows kit and gimbal bearing. My question here is there is the reverse/forward ( worm key) with a triangular head on it. Which way does that face when putting back together. Also I have 78 mercruiser...
  14. grizzreaper

    1968 Johnson 15 hp

    Hello I have a 1968 Johnson 15 hp. Was told it was a 18 HP but searching on the net it comes up as a commercial 15 hp with a fuel mix 24:1 .Is this information correct. Model#WA-14M. Serial# C586349. I have shifter cables for it but looking for bolt size to connect the forward/reverse cable...
  15. grizzreaper

    Wiring diagram for 3.0 mercruiser

    Ok I been looking all over .I have tried different sites and Google.i took a donor block and took my valve cover, flywheel, carb,manifold, rear engine mount,coupler, fuel pump and igntion coil. Going to pull my cap and rotor next.i tried wiring it up but it just won't turn over.i have power to...
  16. grizzreaper

    Mercruiser 3.0 alternator

    I have three alternators. One is a Wilson # 1103197 which I think is a automotive one. It has two wires on a clip, a ground, and a batt post. The other is a Mercury marine# 12449 or J1171 .this has one wire with plug end, one small post, and one big post. Third one has no markings that I see but...
  17. grizzreaper

    Information needed

    I picked up this 1985 glastron boat for the motor and outdrive.i am looking for the year so I can figure out the wiring . Pic#1 is the engine mount tab n the mercruiser serial is 5012180 which I looked up n there is no information. Pic#2 has a serial number by the wire harness 5003045. rest of...
  18. grizzreaper

    1986 3.0 Mercruiser

    I have been on Google and searched on here. Maybe I missed something. My question is will a 1986 3.0 Serial# 0A662126 HP MC1 Model# 01989016 R/MR ALPHA ONE Sterndrive work with a 1985 3.0 Serial # 6901059 HP 140 Model # 01409005 120 HP / 2.5 L 140 HP /3.0 R/MR / ALPHA ONE . My motor which is...
  19. grizzreaper

    Older boat gauges

    Hey I need some help once again. I have older boat gauges in the 1986 StarCraft islander. I see. G P S on the back I am assuming G is ground. P would be power / accc. S would be sender. I want to have all the lights on the gauges on when motor is running. Thanks in advance.
  20. grizzreaper

    1992 3.0 mercruiser wiring diagram

    Hello everyone. I have a 1988 StarCraft islander 21 ft with a 1992 3.0 and I was cutting and rewiring .I cut and now I have no power to key switch. Where can I get a new wiring diagram for this.
Top