Recent content by zymox

  1. Z

    looking for the name of a connector, Force 120hp 1996

    Hi, I'm looking for the name of the 4-pin connector that connects to the ignitioncoil on a Force 120hp. See picture.... I've found the harness new but almost 100$ plus custom and freight is ridiculous pricey for what it is...
  2. Z

    Decrease pitch or radius?

    Hello folks Bought a Bayliner trophy 2002 wa -96 with a Force 120hp -96 a couple of weeka ago and today was supposed to be the first test run day. Ofcourse I smashed the plastic prop mounted (propulse something) and have read alot of forums for a replacement prop. Most seems to be suggesting a...
  3. Z

    140hp 1988 rig assembly problems...

    Hello folks, Long time no seen... I have changed my water-pump today and it really begins here: Upon disassembly of the rig I had to use more power to take it apart than I think is normal. Anyhow it came loose and I did the change. When I now tries to assembly the rig to the rest of the motor...
  4. Z

    New problems, does they ever ends ? Spunn hub or cavitation - I'm to new at this...

    Testing day because my motor has been a real pain in the ... Was out to day on a shinning blank sea and when I added some power to accelerate the boat couldn't plane. It started to act like a worn out clutch on a car, the boat came up to a certain speed and a small raise of the bow then the...
  5. Z

    Bogging question Evinrudee 140 looper

    Hello folks, long time no seen. I hope everything is fine with you guys. My engine has always bogged on me when I gave it more than half throttle and it hasn't really bothered me since half gas is more than enough. Lately it has started to develop a good amount of struggle when I have tried to...
  6. Z

    What smart tabs should I go for?

    Hello all My boat is a -66 Jouet with a 140hp Evinrude going on a deep V hull. It's 6 meter length over all LOA or 19.6' long over all Since I don't have any experience of this I wonder what to go for. Cording to Nauticus they recomend: for 16', 17', 18'+ length and 60 to 150 HP 2 Stroke...
  7. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice Start mode Slow mode Half throttle
  8. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice To day it happend :o) - Splash day arrived with a sunny but windy day so I had to cut the fishingtrip down to 2 hours due to that my daughter felt sea-sick. As you all know, this would not be able without all your help and as promissed I asked my...
  9. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice Problem solved. A good cleaning, a minor grinding and new top-coat applied. The results, wrong color on the gel-coat but still good enough for me. My misses is working hard with the fouling. A copper-based color for the ocean and hopefully it will...
  10. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice New problems, more great advice needed :-( Was down at the boat today and thought it's time to get it going with the outside. I decided that I would like to give it a good wash before I did anything else so I started up the old pressure washer and as...
  11. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice New update in pictures, Got some work done this last week. The motor is mounted and it looks like a match to that boat. Only a few hundred small stuff left to do :-) Nice Perfect match & solid as a rock. Thanks all good ppl. helping me out. Maximum...
  12. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice Hello warnie100 The problem I had in that picture was that when I pulled the old transom-core out I didn't support the hull good enough causing it all to bend inwards making the transom skin to warp inwards. I had to rise it a bit underneath to make...
  13. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice More progress, unfortunately my work claims a lot of time from me now so I can't work on the boat as much as I would like to. But here it goes: Rebuild/restored transom cap. It was crushed on the middle section so I had to redo this section...
  14. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice Dry fitting the 1:st layer of CSM & the Roving wet No air, feels like a pretty good frame for a stringer. 1:st layers done... Only one more "duo-layer" and then finishing it off with a layer of CSM making it a total of 5 layers. (450g CSM/ 300g...
  15. Z

    More transom problems, need some advice

    Re: More transom problems, need some advice Progress in pictures... With my work claiming more and more time it will take some time between the updates...Sorry 4 this But I'll try to look in to the forum as often as I can to help out if needed. Stringers... How to make em? Well I didn't find...
See more
Top