I have two motors that I picked up for parts. One is an 84 25hp and the other is a 74 35hp.
The 35 has the old school round water intakes and the 25 has the square plastic screens. The lower on the 35 froze and not only split the case(Fixable) but it shoved the bearing carrier so hard it...
As stated.
Shifting from fwd to neutral is hit or miss. Shifting from rev to neutral is easy.
Is there an adjustment for this?
The shift rocker sits in the detent either way, but shifting from fwd to neutral softly (Normally) leaves it in gear but if I hit the shifter with a harsh rapid...
I just installed a SE 200 hydrofoil on my 14' Mirrocraft and Im wondering if anyone has tried "Tuning" one of these for the best possible ride?
The boat rides and handles much better with this on but it is not quite perfect as I still get a bit of porpoising. In the package along with the bolts...
95 25hp evinrude. Will not idle and is very hard to start.
Compression is 110/110, carb was just cleaned as well as coils swapped for ones that tested better than original and good wires swapped for bad. Motor has slight water leak out of the cooling jacket gasket near lower cylinder. It also...
14' alumacraft with about 550lbs people/battery/trolling motor. no hydrofoil.
I had it out for the first time last week and fuel usage seemed excessive.
Diagnosing some issues Im having with this motor and Im working on sorting out the Carb/timing/throttle and I have a question regarding the carb butterfly.
Right now I have it idling OK, but the linkages are all out of whack and I need to know where the butterfly should be sitting to move...
Im refurbishing a 14' boat and Im getting down to needing seat pedestals but Im confused to the different types and their benefits or shortcomings.
Which is sturdier for a big guy, a large cast base (9-10"} or the pole type that goes in a socket?
What about the 1" pole types.
I kind of like...
Planning on converting a 14' mirrocraft into a fishing boat, pedestal seats, lights, live well, trolling motor, etc
Looking at the various battery box/power center options got me thinking there must be a better way to get power to a single panel and then distribute it from there, but I need to...
I have done this once before about 25yrs ago but I have lost the recipe.
I was 20 something at the time so I probably just bought whatever anyway, so heres my plan.
I want the battery in the bow of the boat for weight distribution purposes and also to have it out of the way. The boat will have...
I have this engine and Im looking for the correst motor side fuel fitting. It is the push on type like an airline and the engione serial number is:
217.58622.0
Anyone have an idea where to source one?
Thanks!
I have two 25hp rudes, both tillers and I have some questions. One of these is a runner and the other is a parts unit. The runner is a 96 and Im wondering if there is any difference in the lower unit on this than the lower unit on the 88 parts motor.
Also wondering is the powerheads are same or...
Looking to outfit a 14' mirrocraft with a floor and pedestal seats but I dont know what to buy.
Are the D rated Driver seats with the 150lbs side load rating good enough when properly secured for all boating situations?
No plans on jumping my boat or going outside the inlet:eek:, but I do...
The engine from this thread. http://forums.iboats.com/forum/engin...questions-here
Figured Id start a new topic for views.
After being run on the stand and being left to rest for a bit I think the motor is flooding out. Its east to pull over if I run it, shut it off and restart right away...
Hello there boater people!
Just getting back into boating after a long haitus and picked up a 14' morrocraft about a month ago.
Looking around CL for a motor I found a 96 25hp Evenrude listed for $50. I figured that it would at least be a platform for a rebuild, but lo and behold, it...
