I found the perfect candidate for my next restoration. It’s an Aquasport family fisherman 176 I believe it’s the same hull as the osprey
The boat has a very nice ride
The stringers are foam filled and the deck is built like a tub inside the boat
Does anyone have any suggestions on removing...
My 1978 85hp was idling well and trolling leaving the marina it was running fine but when I accelerated it started going faster and suddenly just slowed down to trolling I tried pumping the primer bulb until it got hard again and after a short 1sec delay it would pick up speed and then slow...
I just replaced the startor solenoid on my 78 Johnson 85hp
I wired everything back the way it was
now as soon as I switch my battery on the starter images and the motor wants to start without turning the key
any ideas what could be wrong?
my 1978 Johnson 85hp idles well and at 5mph it runs great
as soon as I open up the throttle it accelerates for a second then bogs down
if I wait a few minutes it will do the same when I apply the throttle but if I don't wait and immediately apply throttle after it bogs it won't accelerate for a...
I was rinsing my motor today on muffs after a day in salt water
when it was running some how my negative wire broke at the terminal on the battery
did I destroy my rectifier? by running a few seconds with no battery connected
I have a 2 wire (blue & green wires) power tilt n trim
my control box has just the switch
can someone point me in the right direction to wire it up
do they sell a kit with the relays or whatever I may need to wire it up
ive been having some issues with my 1984 70hp
bogging out when I apply throttle
I just bought a new compression gauge to
I'm getting readings of 93 92 90
its a harbor freight compression gauge but those numbers just seem way to low?
I have a 1984 70hp it starts and idles great yesterday going out from the ramp it ran fine through the no wake zone
when I hammered the throttle it just bogged down
on the way back to the ramp it struggled just to troll
I had this happen last time out so I cleaned the carbs the primer bulb...
I recently got another boat it’s a center console
and my 84’ Evinrude 70hp has side mount controls
I was looking around and I found this top mount control
dies anyone have any experience with these ,will it work?
(I’m not worried about the wiring)
or can anyone provide some ideas/pics of how I...
Well what can I say
here I go again
with all the help from you fine folks on my Glaston V196
i decided to do another boat
this time it’s a bayliner trophy 1910 center console
first off horrible workmanship the tabbing all came off with a prybar with little effort and of course all the wood...
I’m have a 1983 evinrude 70hp on my boat I have 2 6gal portable tanks under the splash well I have room to put the tanks under my center console so it would be about 7- 8’ of fuel line to get to the motor Could I run that long of a fuel line or will it not work?
im looking for a automatic Oiler removal kit for a 1990 mercury 3cyl
mom looking for the best way to bypass the Oiler
I know the make a plate to cover there the pump goes
anyone know where I could find one
or if anyone any tips on how I could bypass the Oiler
move checked online but can’t...
I has posted earlier about a Mariner 90hp outboard
so I did end up buying it
but I’m unsure of the year or model
the tag on the bracket is gone
but I found this on the power head
anyone have any idea?
(359558) serial num?
I've been looking at a free outboards the last few weeks to replace my 1984 evinrude 70 hp
so far I've looked at a Mariner 90hp
Tommorow I'm going to look at 73' 85hp
Will the controls from my 70hp work with this motor
And are these motors generally good or is there anything I should keep an...
