Recent content by Bill Wilson

  1. B

    Rollers or bunks

    I have a 1964 starcraft -- and need a new trailer. I am told a roller trailer is not the best for a riveted boat like the starcraft I have. It is easier to find a roller type trailer rather than a bunk, but I dont want to damage the hull. I appreciate your thoughts. bill
  2. B

    tire size on my trailer

    I have a 1962 Starcraft Jupiter that came with a tilt trailer. Any chance anyone would know the name/manufacturer of the trailer? Also the tire/rim size that would probably be on it. I don't have either the boat or trailer at home, and I am trying to figure out what these might be. Thanks...
  3. B

    electrical grounding to aluminum hull

    I am rewiring my aluminum boat. Should I ground the hull? I was thinking about running a wire from the negative side of my battery to a buss under the dash for my accessories. Thanks Bill
  4. B

    Petit 6455 aluminum primer

    I am repainting my starcraft (aluminum) boat. Instead of stripping the entire boat, I sanded/feathered the old scratches and roughed the rest of the surface. The Petit primer says not to use over old paint. The paint left on the boat is sound --- do I have to spot prime, or do I have to worry...
  5. B

    Ignition pigtal - 1993 Merc. 60 hp

    I have a 1993 Merc 60 hp. Recently I purchased some quicksilver gauges that I intend to connect to the short 5 pin pigtail that comes out of my remote control box (commander 2000, I believe). The pigtail also has a brown wire which doesn’t run through the pin – what is it for? Also, do any...
  6. B

    Quicksilver Guages

    I just received a set of used quicksilver gauges. I am hoping to install them on my 1993 60 hp mercury outboard. Does anyone know where to get installation instructions and/or sending units? The set consists of MPH, Tach, Water Temp, Tilt, Battery, Fuel and Oil.<br /><br />Thank you<br />bill
  7. B

    1993 60 hp Merc - Power loss

    I recently purchased a used 1993 60 hp Merc. It runs good but periodically and without warning it loses power as though it is running on two cylinders. Sometimes it will cut in and out while running full throttle. I have checked the fuel pickup which seems to be ok. The plugs look fine. I am...
  8. B

    Does alarm work?

    I recently purchased a 1993 60hp Merc. When I turn the key on I don't get a test beep. I am concerned that maybe the warning system does not work and I will ruin the engine if it overheats or the oil pump quits working.<br /><br />How can I test it to make sure it is working?<br /><br />Thanks...
  9. B

    60 Hp Serial #OD203978

    Anyone have the date of birth for this?<br /><br />thanks
  10. B

    1964 40 hp Evinrude Big Twin driveshaft

    Model #40453S / Serial #E02622<br /><br />I just dropped the lower unit on my 40 hp. I was expecting to find a splined end or key at the top of the drive shaft but it was smooth. As a complete novice, I thought there would be a positive connection at the top. Am I missing something or is the...
  11. B

    40 hp Evinrude - lower unit removal

    I have a 1964 40 hp Evinrude Big Twin Model #40453S / Serial #E02622. I am trying to remove the lower unit but if won’t drop down. I have disconnected the shift linkage but the drive shaft won’t seem to come loose.<br />The pinion gear on the lower end is rusted to the shaft.<br /><br />Any...
  12. B

    20 hp Johnson - clutch dog replacment

    I have a 20Hp Johnson – Model #FDL-20C / Serial #J2696570 (1966?). <br />The engine was slipping out of gear. I inspected the gearcase and it looks like the clutch dog needs replacing. It was turned around once since the reverse aspect was good, but now it needs replacement.<br /><br />Can...
  13. B

    40 hp 1964 Evinrude Big Twin - gears

    I punched a hole in the lower gearcase cover and now the gears need to be replaced. Does anyone have a source for these parts? Model #40453S<br /><br />Thanks<br />bill
See more
Top