Recent content by AZSenza

  1. AZSenza

    Pyle PLMRA420 Install

    I'm about to install a Pyle PLMRA 1000w 4 Channel amp to replace a 20 year old automotive 400w Koiler that blew its fuse. It will be driving 2 Bose Marine Speakers and 2 Punch Automotives. I'm also using a Fosgate 2 Ch 320w bridged to drive a Memphis 12" sub.Wiring is all 4g direct to battery...
  2. AZSenza

    5.7 TBI Unit

    Well, while changing my intake manifold gaskets I found out a few things... My intake is a Hi Performance Chevy Bowtie Marine manifold p/n 14096242, with an adapter on top for the TBI. My 1997 5.7 IS equipped with a roller cam, even though Mercruiser told me it was flat tappet by SN. The TBI...
  3. AZSenza

    5.7 Intake front seal leak

    I've had a slight oil leak for about 2 months and it looked like it was coming from the dip stick tube. I washed it down and same thing although I started to suspect the front intake seal, well this past weekend I found it! Front intake seal. Any suggestions for intake manifold gaskets, its a 97...
  4. AZSenza

    Running Lighst Fuse Blows

    Hi all, Running lights were working fine, Last night, I hooked up the plug (7 Pin) lights came on then blew the running light fuse on my truck. (Truck has its own fuses for all trailer items). Truck wiring looks good, I suspect the trailer but where to start?
  5. AZSenza

    Engine Hatch Switch

    Hi all, I have an electric engine hatch ram with a relay box. I took the wires off the switch and cant remember where they go! Being a DPDT, where do the 2 wires hook up?
  6. AZSenza

    Drive Rub Plates For Bravo 3

    Im talking about the thin plastic shims located on the Upper housing that contact the gimble housing when trimmed in the drive range. Its not listed in the parts break down on my Bravo 3. Anyone know where to get them?
  7. AZSenza

    Anyone with an Electric Engine Hatch

    If anyone can post picks or email me the diagram of the hatch switch. I have the control box in the back and switch at the helm. It just stopped working the other day and I'm afraid while troubleshooting I may have crossed wires. I'm about to bypass the control box with a new switch but thought...
  8. AZSenza

    Engine Hatch Blowing Fuse???

    I have a problem I cant figure out. 1997 Larson 226, today the Electric engine hatch went up then NOT back down! After much troubleshooting, the fuse in the control box is fine, the fuse from the battery to the switch keeps blowing (30a). I've checked wires for a short, i dont think thats it and...
  9. AZSenza

    Water in oil and cylinders

    5.7 Mercruiser, raw water cooled-Friday I tried to test fire the engine after changing the oil (it had VERY little water in it, so little I didn't notice it till later), it was hydrolocked, I drained the water, cleaned the plugs put oil in the cylinders and she cranked right over and ran great...
  10. AZSenza

    Alignment Tool

    Does anyone know WHERE to get an alignment tool in the Phoenix area?
  11. AZSenza

    Please Help in Phoenix

    Solicitation not allowed in the forums.
  12. AZSenza

    Bravo U Joints

    I KNOW this question has been asked before but I'm asking again because I can't find it. What p/n u-joints fit the older style (1997) Bravo's. I'd prefer an auto part number but if not thats fine too. Thanks
  13. AZSenza

    Trailer Tires and Rims

    Hi all, a question, my trailer has worn out 13 in tires and wheels. I want to go bigger and would like to know what truck wheels will fit, I've heard ford ranger or jeep with a 5x4.5 in bolt circle will fit. Any suggestions? Its for a 22' Larson.
  14. AZSenza

    Bravo III U Joints

    Excuse me if this has been covered, I couldnt find it. Does anyone know of any part numbers for Bravo III u joints that might be found at parts stores? Thanks
  15. AZSenza

    gimble bearing driver

    What have you used to drive the gimble bearing into place, besides the Merc tool!
See more
Top