putting engine back togather, Torque???97 vp 5.7gl plkr

T

todd mendenhall

Cadet
Joined
Apr 25, 2011
Messages
6
manual says final torque on heads 41 fps on short bolts 48 on meds and 56 on longs, this doesn't seem like alot. Am I reading this correct???? Also should I remove metal inserts on intake gaskes? VP manual says follow manufactres directions for gasket used and VP Gaskets have no direction???
 
Don S

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

manual says final torque on heads 41 fps on short bolts 48 on meds and 56 on longs,
Click to expand...

What is the manual number you are using ??????

Have no clue what manual you are using or what fps stands for, but your numbers are also wrong.
The picture below is from the OEM service manual.
NOTE: On the first pass, all bolts are tightened in FOOT POUNDS , in the next step they are torqued in DEGREES not ft. lbs.


attachment.php
 

Attachments

  • Untitled2.jpg
    Untitled2.jpg
    44.8 KB · Views: 0
T

todd mendenhall

Cadet
Joined
Apr 25, 2011
Messages
6
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

Can you tell I'm just a hobby mechanic??Your Right I'm Using Manual #B771-2. I Was Converting Nm To foot pounds, didn't notice the degrees sign. I have a Proto Torque wrench that reads foot pound and nm. The dgrees has thrown me for a loop. Can I convert?
 
C

craze1cars

Lieutenant Commander
Joined
Dec 26, 2004
Messages
1,822
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

There is nothing to convert, manual is just referring to high school geometry. There are 360 degrees in a circle...180 degrees in a 1/2 circle...90 degrees in a right angle, etc...

Degrees are just telling you how much farther to sweep the wrench after reaching the torque spec given. As for a tool that would tell you what the numbers mean...you'd need a protractor...a torque wrench won't do degrees.
 
Don S

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

No wonder all the information is wrong, that's a clymers junk manual. Throw it away, they have so much wrong informtation in them it's a wonder anyone can put an engine together with one.
Here is a list of the manuals for your engine, download them free.
http://www.4shared.com/dir/14518392/2d00c0cc/LKsharing.html
You can not convert degrees to ft lbs, you need to use a degree wheel shown in the link below. You may be able to rent one from AutoZone, they are easy to use and come with instructions.
http://www.autozone.com/autozone/ac...od1-b2c1?counter=0&itemIdentifier=141510_0_0_
 
T

todd mendenhall

Cadet
Joined
Apr 25, 2011
Messages
6
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

Thanks! Now I get it. Decision time??? I have torqued to the above mentioned specks can I salvage my work or should I start over???
 
Don S

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

You need to start over, with new head gaskets. You have already crushed them improperly, and nothing will be accurate after that.

You could also revert back to the old method of torquing Chevy heads to 65 ft lbs. Just tighten all your bolts to your present 56 ft lbs you have on your long bolts, then follow by going to 65 on all in the proper sequence.
I wouldn't, but that choice is there if you want to try it.
 
T

todd mendenhall

Cadet
Joined
Apr 25, 2011
Messages
6
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

Thanks, Great help, I won't make that mistake again...I'm starting over just to easy at this point to do it right. What can you tell me about the volvo penta intake gasket on this boat. The old gasket did not have the matal inserts?
 
Don S

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: putting engine back togather, Torque???97 vp 5.7gl plkr

I don't recall ever seeing inserts in those gaskets. Can you post a picture of them?
 
You must log in or register to reply here.
Top