Search results

  1. bassboy1

    '86 Johnson 50 hp, rough idle, rich on one cyl

    1986 Johnson 50 hp. VRO engine, VRO has long been removed/disabled by previous owner. Unknown history, other than 'ran when parked,' and has been sitting for 6 years. I've got everything running fine, except I'm currently dealing with a shaky idle. Engine starts very easily (this one has...
  2. bassboy1

    '85 Suzuki DT65 carb issue after cleaning. Is ultrasonic cleaning an answer?

    I've been struggling with this issue for the past month or so. I've never run this engine - it came as a parts engine with another one I've purchased, but was told that it did run before. I swapped this DT '65 powerhead into service on my outboard jet. I knew it had a carb issue, and a broken...
  3. bassboy1

    '89 Suzuki DT55 intermittent power loss/shutdown

    I have a 1989 Suzuki PU55 Jet (factory installed outboard jet, but from the midsection up, it?s a DT55, so we?ll call it that). It?s been running fine until a weeklong trip earlier this month. It's set up as a tiller, so a key switch is the only thing hooked up, no gauges, warning lights...
  4. bassboy1

    Shareaproject.com issues....?

    It's been quite a while since I've last logged on to this forum. Not really sure why, guess I got busy, and we all know how that goes. Since I know a lot on here use(d) that particular site, I figured I'd inquire here. Anyway, I've been using shareaproject.com for awhile, as a handful of...
  5. bassboy1

    Horsepower at the pump.

    My next boat project is one to use a jet ski motor in a 14 - 15 ft. jon boat, to run shallow rocky rivers, much like this guy. http://www.tinboats.net/forum/viewtopic.php?f=21&t=8385&hilit=seadoo Anyway, I found my engine, 650 Rotax out of a 1993 XP. Wasn't quite the engine I wanted, but I...
  6. bassboy1

    Late '60s 6 hp cooling issue

    I have been doing a little work on this late '60s 6 hp Johnson I picked up for a song. Because the motor is missing the ID plate, I only have the serial number to go by. Wbeaton and I have guessed it to be a 1968. If someone has a year list that goes into the 2.75 million serial numbers, I...
  7. bassboy1

    Thermostat and pressure relief

    For whatever reason, I have never bothered to take the time to learn about thermostats on an outboard. Thus, while working on a 50 hp Johnson, I have discovered a need to figure them out. What we are working with is a 1979 Johnson 55 motor, that at some point, had the powerhead replaced by a...
  8. bassboy1

    Outboard inspecting questions.

    Although I circulate outboards through here from time to time, I have yet to purchase one believed to be in running condition, where a compression test or lower unit oil inspection would be a deal breaker. So, I am not sure about what is the proper method about inspecting one of these. Most...
  9. bassboy1

    Shoplifting dog

    Watch the video along with it. Shows the surveillance tapes. http://www.wsbtv.com/family/18358048/detail.html#-
  10. bassboy1

    1981 Yazoo Jon boat conversion.

    Keep in mind, I am a 15 year old, and have very little experience working with metals, especially aluminum. This is definitely as much of a learning experience for me, as it is a hobby. Bought this hull and trailer for 600. Planned on making an all around boat, with a leniency towards bass...
  11. bassboy1

    Police comments.

    These 16 Police Comments were taken off actual police car videos around the USA 16 "You know, stop lights don't come any redder than the one you just went through." 15 "Relax, the handcuffs are tight because they're new. They'll stretch after you wear...
  12. bassboy1

    Deep cycle charger questions.

    Well, actually has nothing to do with the deep cycle batteries themselves, but the starting batteries. The charger that I used to charge my starting battery finally quit. It is now charging 1/3 of what it is supposed to ie: 2 volts on the six volt setting, and 4 on the 12. Seeing that we have...
  13. bassboy1

    1990 Tohatsu 40

    I am considering replacing the 1975 Evinrude 40 tiller on my boat with a 1990 Tohatsu 40 3 cyl. on Craigslist right now. Couple questions. First of all, what is the weight of the Tohatsu? I think it is 158. Secondly, how well does this thing troll? Being what my boat is, a kicker motor is...
  14. bassboy1

    '75 40 spitting at idle

    Attempting to tank-tune engine following repairs. Motor is 1975 'rude 40555. Rebuilt lower unit. Rebuilt carbs. New points, plugs and condensers. Compression even @ 120 psi. Believe I have synched carb and ignition correctly, but seloc manual is vague, contradictory and confusing. Initially...
  15. bassboy1

    Anyone converted a B&S to stick steer?

    No, I am not planning on getting a B&S four stroke, nor do I have one, but I might have something up my sleeve. If someone has done this to theirs, I would love to see some pictures. It won't just hook right up to a set of controls obviously, but I think I could make something work.....
  16. bassboy1

    Kicker setback and height question

    I am planning on running my Evinrude 4 deluxe as a kicker on a Yazoo 1542. The boat will have a '75 Evinrude 40 as the main motor, and has a 20 inch transom. The 4 deluxe has a short shaft, of course. I picked up a nice extrusion at the scrapyard this morning, that will give me the setback...
  17. bassboy1

    2 piece lower unit sealer

    What sort of sealer do y'all use between the upper and lower section of the gearcase housing, on the late 60s and 70s smaller hp lower units? They no longer sell the spaghetti seal for the '75 Evinrude 40 I am working on. We have a couple ideas, but want to hear other opinions. Also, around...
  18. bassboy1

    shareaproject issue

    Can pictures be loaded onto shareaproject from photobucket, or do they have to be done from the computer?
  19. bassboy1

    Too much corrosion, or overly worried?

    This is presumably a 1986 Mariner 40. Normally I am a Johnnyrude guy, but I may have something up my sleeve with this. The woman says the flywheel spins freely, but hasn't been run in 2 years. Now, I have some pretty ugly motors, but that is from other issues. Is this too much corrosion to...
  20. bassboy1

    At what point....

    ....do you throw in the towel? I have a 1974 Evinrude 40 longshaft that had been in the garage ever since we got it for whatever reason. Upon disassembling the lower unit, I found that it needs a new prop shaft, all new bearings, new bushings for the shaft gears, all new seals, the seal...
Top