Search results

  1. B

    1990 Johnson 88 - Where does this nipple get connected?

    Can someone tell me where this nipple gets connected to? It is part number 325659 and is item number 6 in the parts diagram attached. It's not one of the 4 check valves, it's another larger nipple on the bottom side of the intake manifold below the lower carb.
  2. B

    1990 Johnson 88 stumbles at low rpm

    As stated in the title I am having some issues at low rpm. The motor starts idles and runs fine however when going to throttle up on the water there is a slight miss around1500- 2000rpm. If I throttle past it, the motor revs higher and the issue goes away. To give a history this motor recently...
  3. B

    2006 Merc 25 EFI lower unit removal

    Hello all, I'm looking to replace the impeller on my 25EFI along with diagnose a noise that I get when in neutral. I have a service manual but am confused on how to disconnect the shift linkage on this motor. Do I have to push out the number 5 pin on this diagram...
  4. B

    1985 Johnson 40HP missing at idle

    I have the motor above and it sounds/acts like a harley motorcycle when it is idling. It will shake and sputer but it stays running. The motor is a little hard to start when cold but will start right up if it has run. Above idle it smooths out and runs just fine. I have cleaned the carbs and...
  5. B

    1985 Johnson 40hp no power

    I was out on my boat the other day fishing, the motor ran well till the end of the day. I fire it up and start driving at about 3/4 throttle moving up to full when I suddenly lost power. The engine would not rev up past about 1/4 throttle. It would only bog. If I kept the throttle in a more open...
  6. B

    Mercury 25 or 30 EFI reviews

    I've searched the forums and haven't come up with much on these motors. I am thinking about putting one of these on my 1985 16 foot lund pro pike. Currently I have a 1985 Johnson 40 2 stroke on there. Does anyone have any feedback about these motors? I know I'll be losing some power and gaining...
  7. B

    1985 Johnson 40 Starter Squeel and no turn over

    I took my boat out today and ran into a problem. It started up fine, after a while I ran into my problem when I shut the motor down and tried to start it back up. I Hit the start button, the small sprocket bendix? moved up and half engaged the fly wheel and the starter made a terrible...
  8. B

    1985 Evinrude 30 HP idle issues

    I have the motor stated above that will not idle. It will start up and run at about 1/4 throttle, just before the timing gets advanced above the carb but it will not run any lower. I have replaced the plugs, rebuilt the carb, and rebuilt the fuel pump. I just can not seem to get it to idle. I...
  9. B

    Lund pike restoration

    So I have decided to tackle replacing the floor in my boat and possibly changing the floor plan. I have a couple of questions though. 1. When replacing the floor what plywood do I need to use? Can I get by with regular but epoxied wood or do I need marine plywood 2. What are my options...
  10. B

    Livewell help

    I recently purchased a 1986 lund pro pike. I love the boat but need some help with the livewell. First off where can I get a new aerator tube, the original one seems to have broken in the shut position. Second how does the plug system work? Can I get some sort of stand pipe so that it'll...
  11. B

    Where to get a new occupany placard

    I recently purchased a 1986 blue fin 16 foot aluminum boat. The previous owner converted it to a duck boat and painted over EVERYTHING. He then decided to pull the paint off the placard which erased it all. Is there anywhere I can call to get a new one w/ my hull ID. I called brunswick but they...
  12. B

    Deck replacement questions

    I have been looking around the forum and am thinking about replacing the deck on my 1986 Bayliner Capri 16ft. It has one soft spot from where everyone gets in the boat when I got it and it's just bothered me. I'd also like to take out the back to back seats and put it captains chairs. Ideally...
  13. B

    Force Prop help

    I have a 1986 bayliner capri 16 foot with a force 85 motor and ended up with a michigan wheel vortex 13.25x17 prop which works great when there is nothing on the boat. When I'm out with other people or out fishing w/ my equipment I can not seem to make it up to full WOT rpms. I can only make it...
  14. B

    I have a Tach to sell

    I have a 20 pole tach to sell but I can not seem to find a spot to sell it on this forum, is there a place?
  15. B

    kicker mount question

    I've got a 1986 bayliner capri 16 foot and I just got a kicker motor mount for it. I was looking at my transom and realized it does not have wood all the way across. Is this an issue for mounting this? Should I cut some wood for stability on the back side of the transom? The swim platform on the...
  16. B

    Where can I find a throttle force 85

    I've got a 1986 force OB on my bayliner that I'd like to put a new throttle in. I'd like it to have the tilt and trim on there so I could reach it from the outside of the boat. I wouldn't even mind having the ignition there too. I have found some online but am not sure if they'll fit my Force...
  17. B

    Battery recomendations

    I have a 1985 bayliner capri w/ an 85 OB. The people before me just threw a cheap car battery in there and it worked about half a season. I ended up just using the red top optima out of my truck when i brought it to the lake. I am in the market for a new battery do I just need a marine starting...
  18. B

    1986 capri bimini top ideas

    I bought a capri about 2 years ago and the previous owner had the original top but did not have the poles to put it up. I was wondering if anyone has a picture and or ideas of where I could get the poles and hardware to set this up.
  19. B

    Tach Troubleshooting

    So I got a tach for my 1986 force 85. 20 pole tach, I got it all wired up but it won't work. The needle jumps to zero when power is added, but when the motor is started up the needle doesn't move from zero. I got some other wire today and ran it from the tack back to the motor to see if that was...
  20. B

    where to get a 20 pole tach?

    I've gone to my local marine shops and they don't have any that support my 20 pole force. I feel I could get it hooked up but where can I find one that is not breaking the bank?
Top