Search results

  1. R

    89 Yamaha 40hp autolube cdi

    1989 Yamaha 40SGJD two stroke On the cdi unit for this motor there is a pointer that rotates in relation to throttle position. The mechanism is connected to the throttle linkage by way of an adjustable rod. What is this pointer indicating and how should it be set/adjusted? Thanks rcb130
  2. R

    carb leaks at throat, no float seat available

    Hello All, I am working on a 2002 Merc two stroke 15hp. S/n OT531949, model 15M. I cannot find a carb kit with a float valve needle seat, only a needle. How is one to rebuild the carb without a new float valve needle seat? Everytime I try it, the carb still leaks. Is there a trick or secret to...
  3. R

    Do I need the pulse fitting

    Hello all, I am converting a 1992 v4 120Hp Johnson to a conventional fuel pump. I am using OMC 438559 fuel pump. Do I leave the Pulse fitting on the block and connect that to the vacuum side of the pump or do I replace pulse fitting with a straight barbed fitting for the pulse line? Thanks rcb130
  4. R

    spectrum pro avenger 17 foot 1995

    Hello, replacing ignition switch on the above boat. Now it will not turn over. Gauges work. Here is how I wired it, I thought it was like the original wiring. It is a push to choke 6 terminal switch exactly the same as the original. C- Yel/blk S- Yel/red M- Blk/yel I- Purple M-Blk B- Red/blk...
  5. R

    Need some advice

    Hello All, Just purchased a 1992 Johnson 120 Hp V4. Model J120TLAND, S/n G03002936 Motor starts and idles for approx 30 seconds and dies. Will immediately restart and idle for 25 seconds and dies. I am looking toward a fuel delivery problem. Previous owner claims to have rebuilt carbs, replaced...
  6. R

    Need auto enrichment valve "0" ring

    pvanv, try the photo again area circled in red is what I am trying to remove. It has a screwdriver slot like a jet would have. rcb130
  7. R

    Need auto enrichment valve "0" ring

    Hello 2006 Tohatsu 18Hp model MFS18B2 S/n 06265OXF PVNV or Tohatsu Guru. I need the "0" ring size that goes on the auto enrichment solenoid. Can either one of you give me a size or a source to buy a replacement? I do not want to buy the whole valve for an O ring. Thanks rcb130
  8. R

    need help locating a tohatsu manual

    Hello All, Looking for a link to tohatsu shop manual for a 2006 Tohatsu 18Hp four stroke. Model MFS 18B2 3V9 S/n 06265OXF. Just got a Seloc manual and it was a waste of money and time. PVANV or Tohatsu Guru, Can you steer me in the right direction? Thanks rcb130
  9. R

    What is wrong with this motor?

    Hello All, Motor is question is a 1996 Johnson 6 Hp two stroke, model J6REDS. Here is the problem: Overheat after running for approx 3-5 Min. What I have done so far: Replaced water pump with new evinrude pump kit including housing, etc. A complete kit. New vernatherm.. new powerpack compression...
  10. R

    Suzuki DT115 Lower Unit

    Hello All, I do not have serial and model number, all I have is the lower unit. I am working on a 1991 Suzuki DT115 Lower Unit. Can I remove the lower shift shaft without pulling the prop shaft? If so,what is the procedure? Also, What size are the threads in the bearing carrier for the special...
  11. R

    Question for Joe Reeves

    Joe, I am working on a 1970 Evinrude 60Hp with type V electric shift. S/N J10030, Model 60073D. I stripped the original threads using a harmonic balancer puller and a propane torch. Retapped to 3/8-16 and got a propane torch rated to 3500 degrees. Applied heat and cranked down on puller. Still...
  12. R

    bearing carrier bolts

    What is the trick to access the four bearing carrier bolts on a 1970 60 hp Evinrude type V electric shift lower unit? I can get two of them out but the remaining two are so close to the outside wall that a thin wall socket will not go over the bolt head. Any and all suggestions are welcome...
  13. R

    Is there an idle air adjustment on this motor

    Motor is a 1986 Mercury Blackmax 135 Hp. My question is how to adjust the idle air mix on this motor? Is there an adjustment or do I swap out idle air jet sizes? thanks rcb130
  14. R

    1995 Force 90 Hp ate another starter

    Hello All, Motor is a 1995 Force 90 Hp 3 cylinder S/N 0E104323. Customer brought it to me after letting it sit for 2 years without being prepared for storage. It was running but sounded like a chainsaw at wide open throttle. I slowed it down to a near normal idle. It then stalled out, I checked...
  15. R

    anyone used a cdi coil kit 174-6120K1?

    Hello all, I purchased a CDI coil kit #174-6120K1 for use on a Mercury 9.8 Hp S/N A178791. It came with no instructions nor has CDI been able to provide any. Does anyone know if I am to use the existing coil retaining clips to hold the coils in place and what the setback from the outer face of...
  16. R

    What is this used for

    I am working on a 1885 Mariner 75Hp motor. The starter solenoid has a "solenoid insulator" on the solenoid. Does anyone know if this insulator is insulating against heat or electrical flashover? Thanks rcb130
  17. R

    Need a expert on old mercs

    I am working on a 1975 Mercury 65 Hp 3 cyl. S/N 4051811. The fellow who brought the motor to me had removed the flywheel by removing the 8 or so approx 3/8 bolts holding the wheel to the crankshaft hub. Since this flywheel only generates ac to the rectifier, can I install it at any location on...
  18. R

    Does this Merc motor have the infamous nylon washer

    Hello, Does a merc 30/40 Hp jet have the nylon washer under the powerhead that melts and chokes off the water? 1997 S/N OG581304 Thanks rcb130
  19. R

    mercury identification

    I am looking at a 2008 Mercury 150XL OPT Serial no. 1B705987 Family 8M9XM02.52C0 Can anyone provide info on the specs of this motor similar to the BRP model number breakdown describing shaft length, electric start,etc. I can not physically look at the motor as it is 150 miles away on an auction...
  20. R

    1996 9.9 Four stroke fuel pump problem

    I have a 1996 Evinrude four stroke Model E10FEXEDR, S/N G04015605. Took the fuel pump apart to install rebuild kit. Check valves and springs popped out. I check valve disc no where to be found. Does anyone know order of assembly for the check valves, springs and discs? I can find nothing in...
Top