Search results

  1. F

    Inboard 350 dies

    OK I have a non vortec 350 with a less tha 100 hour mallory distributer and a new coil. I also have a new fuel pump and carb on it. The issue is after I start it up cold, starts up perfect and will idle, and let it run for 20-30 min. at idle it will die. Sometimes it will crank back up fairly...
  2. F

    1990 175 Evinrude Alarm Going Off

    OK I am working on this motor for a friend of mine. I changed out the water pump and found that the rubber gromet that goes in the top of the housing was in the wrong place so I put a whole new pump in it. I removed the thermostats and cleaned out the housings. I also installed a new temperature...
  3. F

    140 Tohatsu Alarm

    I have not been on here much as my motor has never given me an ounce of issues. The other day I headed out for a day of scouting and everything was in check. Ran for about 30 min at cruise then pulled the throttle back and eased of to a bank to have a look. Went to power back up to cruise and...
  4. F

    1983 Johnson 90 Not turning up Fuel Problem?

    My 90 is not turning up under load. Out of gear it turns up just fine but when it is under load it sounds like it is bogging and only turns up to maybe 1500-2000 RPM. Sometimes if I hit the choke (it is a primer choke) it will pick up some RPM then fall back off. When I try and start it cold I...
  5. F

    140 Evinrude looper problems please help

    I have a 140 looper that I am having a backfire problem with. I have fiddled with the dwell but have not solved the problem. At idle the motor backfires a lot and a majority of the time it backfires in such close succession it dies. I also need to get it idled down. It idles at between...
  6. F

    Water in bottom cylinder of 40 yammie

    I have a 40 yammie that is an early 90s oil injected motor. It seems I am getting a little water in the bottom cylinder. Do you think it is the head gasket or the base plate gasket. I appreciate the help.
  7. F

    What year is this Yammie?????

    Can anyone tell me what year this serial number or partial number is? I just bought this motor on ebay and it is a 3 cyl 40 HP I am guessing early 90's? Any help would be appreciated.
  8. F

    Tilt and trim wiring?

    Ok I went from a 3 wire setup to a 2 wire setup. I bought a used yamaha 2 wire relay set up and need some help on wiring it. If anyone knows or can look at theirs I would appreciate it. I know the blue and green are the switches for up and down. The 4 black leads (2 from each relay) are grounds...
  9. F

    Tilt and trim wiring question

    OK guys I need a hand. I have 84 115 Yammys yhat have a 3 wire tilt and trim system. I just bought a brand new tilt and trim unit off ebay that was in the Yamaha factory box for 350 buck and it is 2 wire. (I could not pass that deal up period.) I know I can make it work but I need help to figure...
  10. F

    I need tilt/trim units

    I need 2 good used tilt/trim units that will fit 1984 115 Yammies. Anyone know where I can get them without paying more than the motors are worth :eek:
  11. F

    Galvani Corrosion?

    I have a 24 ft Chaperall with twin 115 Yammys. My startboard motor is getting the little galvani corrosion spots on the lower unit and tower housing. I have 2 batteries and the starboard motor battery is isolated from all the accessories it is just used to start the one motor any ideas?
  12. F

    1984 115 Yammy water problems

    I have just put a new powerhead on my 1984 115 Yammy AETO. Naturally accompaning this powerhead I replaced the water pump. Guess what it is not pumping very hard at all. As a matter of fact the faster I go the slower it pumps. I checked with the guy that rebuilt my powerhead and gave me a list...
  13. F

    Know where I can Get Connecting Rods???

    I have a 115 Yamaha 1984 or 5 model that is making a tinging sound. It is not a knock but after talking to a few of my buddies they think it is a connecting rod. I cannot find them here locally for less than 200 bones apiece. I plan on putting a stethoscope on it to find the exact cylinder but I...
  14. F

    Yamaha 115 Model?

    My transom bracket ID plate say 115AETO. I cannot find this in any years parts manual. The boat they are on is an 84 model and these motors are close to it. I need to know the years of these motors to order parts if anyone can help please shoot a reply this way.
Top