Search results

  1. Q

    Can only view one page in forum

    i reset my password and logged in posted a topic in johnson evinrude forum wanted to read some other post but I get error can not connect to site server contact site administrator
  2. Q

    Tilt and Trim assembly fit

    Hope this is the right section for this question. I presently have a 1988 johnson 60hp motor which had just the single shock assist I have the opportunity to purchase a working tilt and trim assembly which is on a 1996 johnson 60hp motor. This would be a parts mortor. Will this assembly from the...
  3. Q

    Johnson tilt assy

    So I stumbled upon a listing for a 1996 Johnson 60 hp motor that needs new carbs and some other items. I presently have a 1988 60 hp Johnson on my boat without trim. My question is would the tilt assy from the 1996 work on my 1988 ? They are asking best offer if the tilt assy would swap out ok...
  4. Q

    tan wire from 1988 60 hp johnson

    Tan wire from 1988 60 hp Johnson. I believe this is the temp warning wire from the engine. The previous owner did not have it wired into the dash, however there is a small red warning light as well as a small round buzzer. My question is can someone explain how to wire this into my fused...
  5. Q

    Tilt and trim addition

    anyone have a ballpark cost to add a tilt and trim assembly on a 1988 60 hp Johnson Modell # J60ELCCR ? Tilting manually after awhile will get to be a pain, I'm not exactly sure if the tilt assist is functioning properly.would really like to get this 16 ft SS Splashed this year
  6. Q

    Bunk placement on roller conversion

    I have decided to change the roller setup on my ez load trailer. My question is how close to the strikes should the bunks be located? The boat is a 1974 16' Starcraft SS. I think I can use the existing mounts with some fabrication work and should be ok. I would appreciate any suggestions from...
  7. Q

    Changing from roller to bunk

    was thinking about converting my old ez load roller trailer to bunk trailer. I was hoping I could get some advice, I was planning on getting some swivel brackets and adding them where the existing roller brakets are and run double flat 2x6 's from about 2 inches behind transom to as far forward...
  8. Q

    Trailer input

    Has anyone had any experience or feed back regarding Venture Trailers I believe out of Maryland. Going to replace my old ez loader roller with a new bunk trailer, reason being old ez loader has a bent spindle, rusted ubolts and also needs new tire and a paint job. Any input would be appreciated...
  9. Q

    Wood on outside of aluminum transom

    getting ready to install new wood transomgetting on 16 ft ss got all the small pitting glazed over with JB weld marine. All bare aluminum inside and out primed with self etching primer and 2 coats of Rustoleum enamel with harder. My question is the previous owner had a piece of 1/2 inch probably...
  10. Q

    Prime aluminum or not

    Removed old transom got new one cut and ready to install. The aluminum have some ver minor pitting which I was going to skim with some JB then sand smooth. My question is should I spray a coat of primer on the inside skin prior to installing the new wood. Forgot to mention boat is a 74 Starcraft...
  11. Q

    Transom wood recommendation

    Have gotten a lot of opinions on this so I figured asked the experts. Got the old transom out in one piece not to bad of a job. Now what is the best replacement wood to use for the new transom? Thanks for your help
  12. Q

    What type of control unit

    This control in presently on my 74 Starcraft controlling a 60 hp Johnson . Can't find any name or manufacture of it it does work but was wondering if I should get something that is a better match.
  13. Q

    93 Johnson 9.9 with 15 hp carb on it

    was going to look at a 1993 Johnson 9.9 with a 15 hp carb on it for my boat. Motor includes controls steering linkage etc. my question is , I know that it won't be a true 15 hp but am I looking at a motor that may give me more headaches such as not idling corectly. The gentleman wants $800 for...
  14. Q

    Soft upper corner of transom ok

    I have a 16 foot Starcraft ss with a soft area on the very upper corner of the transom by the cap only on one side. Motor currently is a 60 hp Johnson. With the rest of the transom in good solid condition will I be ok ie safe running this boat this summer until I get a chance to install a new...
  15. Q

    Shaft length tof trolling motor for 16 ss starcraft

    Not sure if this is the place to post this question . Would like to get my boat in the h2o and need some help in trolling motor shaft length for my boat . Just in case the Johnson quits on me and would like to get back home safely! Is a 52 inch 55# thrust most ok for this boat?
  16. Q

    Below h2o line gouge repair on tinny

    need some advise on some bottom hull repair. Previous owner or before him found a way to get some long gouges in the bottom of the hull thankfully nothing that punctured the hull. However what would be my best bet on patching or filling these gouges in until I do a total restore of this fine 16...
  17. Q

    Price for 60 hp Johnson

    I have a Johnson model J60ELCCR SERIAL G7796071 on my 16 ft SC SS any idea what it might be worth ?
  18. Q

    Installing tach for johnson

    few months back I piurchased an16 ft Starcraft ss it came with a running Johnson 60hp model J60ELCCR I don't recall there being a tach in the dash is this something I can add and where would I be able to get instructions on installing one. Would like to make sure it is running as best she can...
  19. Q

    Installing tach for johnson

    few months back I piurchased an16 ft Starcraft ss it came with a running Johnson 60hp model J60ELCCR I don't recall there being a tach in the dash is this something I can add and where would I be able to get instructions on installing one. Would like to make sure it is running as best she can...
  20. Q

    Motor recommendations

    looking to replace my motor on 1974 starcraft16 foot ss. Due to local hp limits on a lot of water here in Pa. I'm looking at a 20 hp Yamaha. I know it may not get the boat up on plane but was going to change out the prop with a different pitch and go with stainless. I was hoping for some...
Top