Search results

  1. L

    Milky fuel in carb intake force 85hp

    Didn't noticed any, actually the service I did to the pump previously was changing the check-valves so I got to them.
  2. L

    Milky fuel in carb intake force 85hp

    Bad fuel pump membrane... It was new, maybe in the intallation I damaged it.
  3. L

    Milky fuel in carb intake force 85hp

    That picture was before the rebuild, yesterday night I put it back together in the same orientation but with the nut in the outside. I adjusted again to 28° at cranking speed. I have read that the idle timing should not be affected and would not be needed to be adjusted, anyways what should be...
  4. L

    Milky fuel in carb intake force 85hp

    I saw some pictures in the internet from what seems same motor 1989 85HP Force, and this assembly looks to be installed backwards, the adjustment screw falls under the flywhee, (I had it like that before the rebuild but thought it was worng because some other pictures I have seen in the internet...
  5. L

    Milky fuel in carb intake force 85hp

    Thanks I will check that, previous to the rebuild I checked on spark and it was 3/8" strong, I'll recheck. Fuel pump is new and I serviced the pump as well, I don't think that is the issue, I'll take another look. I think I have a Syncronization & Timing issue. My doubts are on the timing, will...
  6. L

    Milky fuel in carb intake force 85hp

    Finally got it to the lake, not the best output, motor started no issues idled good, but it didn't reved up. No more than 1200 RPMs, I dont know what to check now, some how I think its a timing issue, I redo Frank's procedure, see if something is off.
  7. L

    Milky fuel in carb intake force 85hp

    I was reading the Break-in instructions from maxrules.com, and this "You must determine the reason the original powerhead failed. If the problem is not identified and corrected it is almost certain the newly rebuilt powerhead will fail. If a restricted (lean) carburetion problem caused the...
  8. L

    Re- torque head bolts?

    I just rebuilt my motor, and torqued it to spec very low to my feeling and according the sequence, it leaked at the first start, not sure if the torque wrench is accurate or not, it is just a Autozone wrench. I decided to go a little bit higher 22 ft lb, and it did stopped leaking, after the...
  9. L

    Went electric

    Your role changes with the robot, I own a large Neapolitan Mastiff, you can imagine what kind of dog poo he makes. Maybe not the best practice but when I used regular mower I cleaned up the yard 1 or 2 times per week, so when I mowed I didn't step on poo and get messy, now with the robot as the...
  10. L

    Went electric

    I've gone cordless electric with my weed trimmer, is a cheap Black and Decker 21V, it uses the same battery for my hand drills and other tools. It doesn't have the power of gas neither of a corded trimmer but it is so practical just to grab it and start it immediatelly that I don't miss the gas...
  11. L

    Milky fuel in carb intake force 85hp

    random question, last part I installed is the "deflection stop" what is that for? I didn't see an obvious function for that. Item 20 below.
  12. L

    Milky fuel in carb intake force 85hp

    Thanks we'll see how this goes in a couple weeks that I will be able to go to the lake. I'm anxious for that.
  13. L

    Milky fuel in carb intake force 85hp

    Good information thanks, I will follow this.
  14. L

    Milky fuel in carb intake force 85hp

    I aligned the connecting rods until no separation line was visible, just had small issues with one of them but I disassembled and noticed some dirt in between, cleaned out and then reassembled and the separation line disappeared, I think that worked out good. Now for the gas/oil mix 25:1...
  15. L

    Milky fuel in carb intake force 85hp

    Any recommendations for taking it to the lake for the first time, should I run it with a higher gas/oil mixture? I've seen people suggesting 1:40 ratio or something like that.
  16. L

    Milky fuel in carb intake force 85hp

    So i just finished building up the motor today, and it fired up immediately, no hick ups or anything, but I noticed some drops of water leaking through the head gasket, I warmed it up and retightened a little higher than specs suggested, the leak stopped. Compression is now 105-110-105. Seems...
  17. L

    OK I’ve had enough.

    I'm in northern Mexico no snow or rain in months, our lakes are drying, gobal warming is hitting hard here. We still could go out fishing anyday until the lakes completely dries, praying for god Tlaloc for some rain in the area.
  18. L

    Starter fluid everytime....

    Yes I would say this choke was 90%+ closed and that little amount off was enough for not starting by its own, fortunatelly it was a quick fix hoping to take it to the lake to test in real situation. I've used so many times the starter fluid with no issues on the outboards for that how ever I...
  19. L

    Starter fluid everytime....

    It was a quick fix, choke wss not closing completely. Thanks
  20. L

    Starter fluid everytime....

    I do press the choke button and advance the warm up lever, I havent checked if the choke is actually closing the carb completely, I will take a look. I put the startarter fluid directly to the carb air intake. Then crank.
Top