Search results

  1. M

    99 mercury 150 XR 6 warning system not self testing

    99 mercury 150 XR 6 warning system not self testing
  2. M

    Idle Stabilizer bullet connectors discolored

    Can you give me specifics on removing it? What to do with the wiring back to the switch boxes, etc. ? Going to run it in an 80 gal tank, so will the timing and idle adjustments be the same?
  3. M

    Idle Stabilizer bullet connectors discolored

    Thanks for all the good advice!
  4. M

    Idle Stabilizer bullet connectors discolored

    Thanks! I have a 80 gal tank that I can run it in.
  5. M

    Idle Stabilizer bullet connectors discolored

    What should the idle timing be set to, between 3-5 degrees BTDC ?
  6. M

    Idle Stabilizer bullet connectors discolored

    Thanks Dukedog! All healed up now! Got 80 percent strength back but I think it's stronger than that from working out 2-3 times a week.
  7. M

    Idle Stabilizer bullet connectors discolored

    Had a bad fall on concrete last year and had to get a reverse shoulder implant. Finally getting around to removing the idle stabilizer. Any specific info on how to remove it will be greatly appreciated!
  8. M

    1971 Mercury 110 9,8 HP Male Fuel Adapter Problem

    I'm restoring my 9.8 Merc and almost ready to test run it, however I can't find a female fuel connector for my gas tank that will match up to the old 32454 fuel line adapter that's in the lower cowl. I may have to change it out with a newer one that will match up to a female connector. Mercury...
  9. M

    85 Johnson 8 HP MN:J8RC0B

    Need some new fuel hoses. Anyone know what the correct sizes are from the fuel inlet to the fuel pump and from the fuel pump to the carburetor? There is no way to drain the carburetor float bowl after running the motor. OMC manuals say unplugging the fuel line and running until it stops won't...
  10. M

    99 Triton 18 ft Sea flight boat

    Anyone know what size the diameter of the holes in the transome are for the through transome scupper valves? Need to order some but not sure what size to order.
  11. M

    1999 Mercury 150 XR 6 voltage regulators wiring modification

    I modified my voltage regulators to get rid of the bullet connectors and installed a 1 amp fuse holder in the sense wire and a 30 amp fuse holder in the voltage feed line after a new C.D.I. voltage regulator burned out when I turned on the battery switch. Special thanks for the info. I got from...
  12. M

    Idle Stabilizer bullet connectors discolored

    I noticed my idle stabilizer bullet connectors on white/black and red/white wires that connect to the outer switch box are discolored, possibly the bullet connectors are over heating? it's in a 99 Merc 150. Should I cut the bullet connectors off and solder/heat shrink them or get some new...
  13. M

    1999 Mercury XR 6 Outboard

    Was going to power tune my outboard, turned on the battery switch and the lower CDI voltage regulator/rectifier started smoking. Anyone know what could cause this. The ignition switch was not turned on yet and the key was in my pocket.
  14. M

    150 mercury power trim manual release not functioning

    150 mercury power trim manual release not functioning. Backed the screw 4 full turns and can't manually tilt the motor up. Service manual said don't back it out more than 4 full turns.
  15. M

    99 Mercury 150 poppet valve

    How can I remove the poppet valve carrier?
  16. M

    99 mercury 150 divider block

    Does anyone know what the hole in the bottom of the divider block is for?? It is located behind the water pump base and appears to be a drain hole for the water pump. Is this correct?? the motor is a 1999 Mecury XR6 150 HP.
Top