Search results

  1. S

    v6 rigging

    i having problems getting the cables to go neatley through the fitting in the cowl .is there a diagram showing how they all fit together .its a 1999 200 efi
  2. S

    gear box parts

    i,ve just bought a spare gear bow for my v6 200.the box is older than my other one. it looks to need a new shift shaft seal and impellor housing.i having problems identfying the part no i need. this box i have bouht has a spring loaded pin in the of of the drive shaft. it also has plastic...
  3. S

    painting anodized aluminum

    how i paint anodised aluminium. do i sand it then just etch prime . does the anodising need to come off?
  4. S

    prop part no

    i want to buy aprop off e bay for my 1999 200 efi but am unsure of correct part no. is there any where on line i can look to the the right part no of what i need
  5. S

    spare parts

    is there a site that showws exploded diagrams with part no so i can work out what i need
  6. S

    what year

    what year did merc change from inline 6s to the v6
  7. S

    what to measure to deterime if long shaft

    where do i measure from to , so i can tell wheather i have a long shaft motor
  8. S

    paper ?

    i finaly thought i was ready to start glue my nightshift project back together when..<br />the skids on the bottom of my boat are moulded in to it.on the inside this leaves agroove. into this groove it looks like the builder has put solid paper tube to give him an arch and them glassed over this...
  9. S

    Force 120

    Can anyone tell me anything about the Force 120 Outboard/Inboard Engine. I am looking to buy a Bayliner Capri 2050 Deep V Hull but have never come across these engines before. Any idea what year they did Capri 2050 with this engine ?
  10. S

    wot

    my freind has a volvo AQ151B could anybody tell me what the wide open throttle is for this engine
  11. S

    rigging counter rotating

    when rigging counter ritating outboards .i'm right in thinking.the left hand motor on the left side of the boat and the right on the right? what happens if there on vica versa.
  12. S

    testing trim sender

    a while ago the earth wire on 1999 200 efi trim sender unit corroded through.i fixed this worked for awhile. when this happened the trim guauge pointed vertical off the scale.this has happened again.i have cheched and redone earth connection with no difference. how can i test to see if sender...
  13. S

    efi de-carbing

    i want to de-carb my 200efi.unfortualey where i live sea foam is unavaidable .i have mercs spray for this, but i,am unsure where to spray it.on the can it says through the carbs but i don,t have any.do i unscrwew the oxygen sensor and spray through there?
  14. S

    bits in head

    i have a 99 mariner 200efi with sportsmaster gearcase on .Awhile ago i hit a log real hard and had to drill the wood out off the holes.since then i am worried about rubbish in the head because my temps seem abit higher than before. is the best way to flush the head remove the leg and flush back...
  15. S

    keeping alumimium shiny

    i want to put some alumimiun check plate on the back of my boat but am worried about going funny with the salt and general exposure ie white and blotchy. is there any thing to do to aviod this.i was told marine grade but we have a company near us who use this to build boats and after awhile this...
  16. S

    mounting outboard

    what sealant do people recommend for sealing the bolt holes on my transom where my outboard hangs
  17. S

    2 stroke

    does two stroke oil go off . have some that smells of ammonia
  18. S

    engine flush

    when i replaced the poppet valve on my mariner 200efi 1999. i noticed a thin film of salt deposit on the inner passages.i was thinking of using starbrites engine flush on this to remove the salt has anybody used this .any feed back
  19. S

    jack plate

    i have a 18ft vee hulled speedboat called a phantom.on it i have a mariner200efi with sportsmaster gearcase.can any boby advise me on how much set back on a jack plate i would need or is it the more the better? at the minute i am pulling 71 mph using a laser2 23 pitch on a 25 inch transom
Top