Search results

  1. N

    How do I replace the vertical shift linkage in 2005 Yamaha 8 HP 4-stroke outboard

    When replacing the water pump, the threaded connector (for the shift linkage) was frozen and I snapped the vertical shift linkage that goes up to the powerhead section. I don't see a way to remove the rod due to lack of clearance from the powerhead. Is there a good (easy) way to remove and...
  2. N

    '03 Mercury Bigfoot 25 long shaft on a fishing boat w/ 16.5" transom???

    I have a chance to buy a 2003 Mercury Bigfoot 25HP Four Stroke (long shaft) and wonder if it would be appropriate on my 15.5' fiberglass fishing boat (Pedestal seating). The boat has a 16.5" transom. I can not measure the Merc as it is about 6 hours away from me, but I know its a long shaft and...
  3. N

    Yamaha 8hp 4-stroke runs fine up to fast idle, dies out mid-range and faster

    I have a 2005 Yamaha 8HP 4-Stroke. It acted up on me yesterday and I had to return about 5 miles to the ramp at fast idle speed (just past the start icon on the handle). If I tried to run faster, it would die out. It did run pretty smooth at idle/fast idle and would start just fine. Started...
  4. N

    Minn Kota 565Na does anyone have a picture of the cable routing for steering?

    Just bought a used Minn Kota 565Na. Inside the foot pedal one of the cables is broken and I need to fix and re-route the cables thru the pulleys. Does anyone have a picture or diagram of one with the cable routing? Thanks!
  5. N

    Anyone running a Solas prop on a Yamaha 8hp 4-stroke

    I need to pick up another prop. My 2005 Yamaha F8MSHC came with a 8 1/2" x 7 1/2" prop. I have it on a 14' v-hull Lowe fishing boat (1462). I believe the 6hp came with the same prop. The Solas props are much less expensive but only come in a 7" or 8" pitch. I was thinking since the 6hp came with...
  6. N

    2005 Yamaha F8MSHC won't lock in full tilt position

    I just bought a used 2005 Yamaha F8MSHC. When I tilt it to the full position it won't lock in place without me pulling on the bracket by hand. I have lubed all the swivel "points" and verified that all the springs are in place. Is there a common problem here that is easily fixed? Do the springs...
  7. N

    Struggling getting 1973 Evinrude 6hp running

    I really need some expert advise. I picked up a 6hp Evinrude and do not know the history. I tried to start it but it would not start when I first tried it. Ruling out a couple things. I am using the same tank and tank-to-engine fuel line (and fuel) as I tested on a 1975 6hp Johnson which runs...
  8. N

    '73 Evinrude 6hp - setting throttle grip to carb position

    I am getting ready to reassemble the carb to the motor after cleaning/rebuilding, however I know the throttle grip wasn't matching the correct carb butterfly position when I took it apart. Someone had marked a different start position on the tiller arm instead of where the decal shows "Start"...
  9. N

    Evinrude 6hp carb reassembly/installation - gasket sealant?

    I am rebuilding a carb for a '73 Evinrude 6hp. I checked the top secret file, but no mention that I could find of whether or not to use gasket sealant on the carb gaskets. Do I use sealant? If so, what type is recommended? Thanks!
  10. N

    Just bought a 2005 Yamaha 8hp, anything to look out for?

    Hi folks, Just bought a really nicely maintained Yamaha F8MSHC 8hp 4-stroke. Oil and gear lube have been changed annually. It has been used in brackish water, but flushed every time. In Fall its been fogged and sprayed down with WD40. This is my first 4-stroke, anything I should watch out for...
  11. N

    1973 Evinrude 6hp Starter Rope diameter?

    I am trying to order some new starter rope for my 6hp Evinrude (1973). I found the length is supposed to be 56 1/4", but does anyone know the diameter? Thanks, Bill
  12. N

    Questions on full reassembly of '71 Johnson 6hp

    Hi fellow iboaters, looking for some guidance here... I picked up a basket case (almost completely disassembled) 1971 Johnson 6hp as part of a boat purchase. I was told it was running before disassembly (in 2009 I believe). The fellow took it apart because the shift lever linkage had broken in...
  13. N

    Fuel usage in 1970 Evinrude 25HP

    Now that I have it running well, what should I expect for fuel usage in my 1970 vintage Evinrude 25HP at cruise speed? My tank is only 6 Gal...want to be prepared. I am running 50:1. Thanks, Bill
  14. N

    Johnson 9.9 No Spark - help testing sensor/powerpack

    I'd like to ask for a bit of help on the debug procedure for a 9.9 Johnson with no spark. I'd like to tell you what year it is but the serial number/model tag is broken off and the engine has been painted in Camo. It is the model with a Sensor and Charge Coil under the flywheel. 1. Has a...
  15. N

    Spark plug + ignition info for 1979 Merc 45 4.5hp outboard

    We are trying to bring a 4.5 hp Merc outboard back to life. Sometimes it runs well, sometime it won't start. We believe we have narrowed it down to the ignition system. I have looked online and in this forum and have not found the info we need. 1. What is the recommended spark plug for this...
  16. N

    What size threads to pull flywheel on 1970 Evinrude 25HP?

    My engine is 200 miles from me right now and I want to insure I get the correct bolts to be able to pull the flywheel if need be when I go out and work on it. Can anyone please tell me what size threads to pull the flywheel on 1970 Evinrude 25HP? I have the manual, but it only says to use the...
  17. N

    1970 Evinrude 25HP Ran ok, then quit afer 30 minutes and restart but stall

    Just picked up the engine on a boat I purchased, so I don't really know the history. This is a 250002E model. While knowledgeable about engines, both 2 and 4 stroke, I haven't much experience with outboards. Test drove it last weekend on the fuel left in the tank, ran ok. Probably put 20-30...
Top