Search results

  1. D

    CDI power pack issues

    I bought a used CDI power pack for my 1995 johnson 130. It is a 113-4041 part # CDI power pack which I believe is the right one for my boat (J130TLEO) However when I put the power pack on the motor now has no spark. The seller said it was a working power pack but I have nothing. I had spark with...
  2. D

    1995 Johnson 130 Power Pack or Timing Issue?

    My outboard has some issues. It doesnt idle real well which isnt that big o a deal to me. I can get going and the motor runs great for the first 2-3 minutes. WOT runs well and then it will start to miss and "surge" and if I let off on the throttle a little it will clear up. It runs perfect at...
  3. D

    1995 Johnson 130 HELPPPP!!!

    I can not get my Johnson to run correctly. The problem I am having is with the fuel priming solenoid. If the red lever is in the run position I can get it started but it wont stay running. Its like after it burns the fuel from the priming solenoid it just dies??? But if I move the red lever to...
  4. D

    1995 Johnson 130 V4 help...

    I was wanting to know how to check my priming solenoid. I have voltage going to the solenoid and the correct ohms when the solenoid is off. How can I check to see if the thing is working. I cant get my motor started and I have tried depressing the key for 5-8 seconds and I hear no clicking or...
  5. D

    1995 Johnson 130 spark plug wires

    How do you know which spark plug wires go to which spark plugs?
  6. D

    1995 Cajun Fish and ski 19ft

    How can I drain the fuel tank on my boat...I believe that there is some trash in it and I need to clean the tank. Also what is the best way to clean the tank?
  7. D

    Dash Wiring...Help?

    I have a 1995 Cajun Fish/Ski. Only part of the dash gauges work. All the switches for the bilge, livewell, etc work but my fuel gauge doesnt work nor the speedometer. The RPM guage works but it only registers at WOT. How can I trouble shoot this problem. I am very inexperienced with boat...
  8. D

    1995 Johnson 130 shifter height

    I am have to replace my lower unit. I am now ready to put it back on but I have no idea what the shifter height should be and I dont have the measuring tool either. It is a 20" drive shaft. Please help me I need to get this done so I can use my boat again....
  9. D

    torquing flywheel nut

    What do i need to torque the flywheel nut to on a 1975 evinrude 135 and does anyone know what size nut that is?
  10. D

    pulling flywheel

    I have a 1975 evinrude 135. I am needing to pull the flywheel off. I have a flywheel puller but i need to know what size bolts fit into the flywheel. Also whats steps do i take in pulling the flywheel off and is there anything i need to watch for when pulling it off? thanks in advance.
  11. D

    1975 135 evinrude

    My outboard isnt firing well enough to keep it running. Is there any way to clean the stator and see if it helps or what should i do. PLease give it to me in easy instructions.
  12. D

    1975 evinrude 135

    On my evinrude 135 I can get it started when I have the warm up lever about halfway up, but it wont idle in the run position by itself. I have to leave that lever half way up. I can ingage it into forward and reverse without it dying, but when I put it in the water it bogs down and dies when I...
  13. D

    Hhheeelllllppppp!!!!

    I have a 1975 evinrude 135. It will not start unless you have the warm-up lever pulled all the way up or halfway. sometimes it wont start at all. I know that advances the spark with the lever. I check ed the plugs and number 4 cylinder is the only one firing, however when you pull the warm-up...
Top