Search results

  1. G

    1997 Yamaha 200hp Saltwater Series Carbureted twins fuel consumption not even close

    Twin 1997 Yamaha 200 Saltwater Series CARBURETED Both motors Rebuilt powerheads. same props. Both motors run great , both motors have a separate fuel tank. the port motor is burning a lot more fuel than the starboard. Last fill up was 43 gallons on starboard side, 55 gallons on port side. From...
  2. G

    prop results after testing

    1993 Robalo 2120 , 21' center console, T-Top, trim tabs 1999 Yamaha 225 OX66 Saltwater Series AS TESTED: 3600 dry weight, Yamaha weighs like (550), 100 gallons of Gas (630) Coolers, gear, ect. (400), 3 people (550), Total: 5730 Motor trimmed to the same position for each prop, trim tabs in...
  3. G

    2000 Yamaha 225 ox66 idles great bogs off idle

    This is a used motor new to me, I hooked it up with all the factory wiring harnesses and controls. it starts right up, idles good, when i give it gas it bogs, if i pump the throttle it will rev up, once it revs up it will stay there, just cant get there without pumping the throttle, seems to do...
  4. G

    94 merc 200 hole in block ????

    1994 Mercury 200 2.5l . This is on starboard side at the base of the block behind starter mount. looks like it was corrosion??????
  5. G

    94 merc 200 hole in block ????

    1994 Mercury 200 2.5l . This is on starboard side at the base of the block behind starter mount. looks like it was corrosion??????
  6. G

    1994 mercury 200 offshore prop size?

    I have a 1994 mercury 200 offshore . the prop thats on it is an aluminum 3 blade the only numbers i can find on it are 19 16 19. its on a 1994 22' robalo, seems to get on plane good, tops out about 38-40 5500 rpm, with full tank and 3 people and all our crap. fuel economy seems to be about...
  7. G

    1993 Mercury 200 Offshore motor Tilting on its own, wet switch.

    i was out today an it was a little rough and was getting some spray. the motor tilted up all by itself . the tilt/trim switch on the cowling got wet and made connection(i guess) and tilted the motor up when i was running slow in rough seas. Is this a sealed switch? is it just old n not sealed...
  8. G

    1993 mercury 200 offshore tilt/trim sender?

    Maybe im crazy or just blind but i cant seem to find the tilt/trim sender for the gauge.
  9. G

    1993 mercury 200 offshore, water pump/pisser?

    i recently purchased a 93 Robalo with a 93 mercury 200 offshore only used in freshwater. On muffs (i know) It was not pumping water out the telltale stream. so i replaced the water pump, and now it pumps water out but at idle it takes about 10 seconds and it streams out kinda erratic. at...
  10. G

    1993 mercury 200 offshore. oil injection repair (removal?)

    I have searched and havent come up with the answers i was looking for. I just got a 1993 2120 robalo with a 200 mercury offshore. I didnt get a lot of history with the boat. Anyway, It fires right up and within a few seconds the alarm goes off, fast beeps. The remote oil tank is full and...
  11. G

    water pump, johnson 110

    i have an 89 johnson 110, i just replaced the water pump, i noticed that it leaks water at the seam above the lower foot, it did leak a little stream before but now it leaks a few streams, the book called for no gasket or any sealer, i did scrape all the corrosion off which is why its leaking...
  12. G

    johnson 110 no spark

    ok after solving the overheat issue at high rpm we got to enjoy the boat for 2 days. WOOOOHOOO then we were running at 4800rpm and wham, nothing it just shut off, i checked everything i could and had tools for, and no spark, now im home and trying to troubleshoot it, i did unhook the single...
  13. G

    1988 Johnson 110 overheat at high rpm

    Re: 1988 Johnson 110 overheat at high rpm thanks i feel the same way. i ran it all day today with no overheat problems, here is a pic of the deflectors. ,
  14. G

    1988 Johnson 110 overheat at high rpm

    i have recently bought a 1991 19' center console Proline. It has an older 1988 Johnson 110. it overheats at high rpm. with 3 people in the boat it will run 4300 all day long and not overheat, bump it up to anything over 4500 the alarm goes off. I replaced the thermostats and it didnt seem to...
  15. G

    1960 14' Lonestar Malibu???? aluminum

    I just picked up this boat today, I cant find any numbers or a tag on it anywhere. It looks like a 1960 14' aluminum Lonestar Malibu. Can anyone ID it for me? Not sure what to do about a title, did they title them in 1960? Heres a few pics.
  16. G

    5.7 fuel pump

    im currently rebuilding my 1986 5.7 mercruiser. just before the cylinder wall rusted thru, (another Story, New Block) the fuel pump went out. in a bind i put an automotive pump on. The original marine pump Part#861678a1 i still have, is it rebuildable? if so where do i get the new parts. also...
  17. G

    Jackshaft ujoint part number

    does anyone have a cross reference number for mercruiser ujoint number 61221t. its for the 2 ujoints in the jackshaft. What about the other bearings they are 30-93944a1. thanks
  18. G

    mercruiser pre alpha new gimbal boot tear???

    ok I have a 1988 Chris Craft 21.5' center console, 5.7 under the console, drive shaft that goes back to an alpha drive, with a new sterndrive engineering, unit. Just put new gimbal bearing, all new boots, and new limit switches. Took the boat out today and adjusted the shift interrupter...
Top