Search results

  1. B

    Mercury 225 Opti DTS Harness

    I recently purchased this motor used with no controls or harnesses. I contacted a mercury rep and got the part numbers they recommended. 1BO72977 is the serial for this motor. The problem I have is with the command module harness. It is missing pins H,J and N on the 14 pin connection. My motor...
  2. B

    Hpdi or not

    Thinking about repowering with a 250 hp 2007 Hpdi motor. This is a new unused motor. I have thought about finding an ox66 used motor also. I would love to have some input on whether this motor will cause heartaches or not. I currently have a 225 looper on the boat. Any advice????????
  3. B

    225hp Johnson Timing Question

    I have a 1991 225 TLEIC. My question is can I check my wo timing without running it. The book says to run it at 4500 to 5000 and check it there. I would like to get it in the ballpark before I take it to the water. Can I take my throttle cable off and advance it that way while turning it over...
  4. B

    225hp johnson carb question

    I have a 1991 JTLEIC 225 hp that I am redoing the carbs on. I am doing this for 2 reasons it leaks gas on some of the bowls and it will not stay running at idle. It will fire right back up when it dies. I suspect the idle problem is a badly engineered side plate. I will use a fender washer under...
  5. B

    Weak spark on a 15hp

    I have a 1986 15 hp Johnson that I am having a hard time starting. The spark air gap according to the book is 1/2 inch. I am getting about 1/4 at the most. That is when I pull it as hard as possible. If I pull it half heatedly I get no spark at all. The charge coil ohms out at 540 ohms. Sensor...
  6. B

    225 johnson dieing at idle in gear

    I have a J225TLEIC that I need some help on. It runs great pretty much from 2000 rpm all the way to wide open. It will start and idle. The problem is going from idle to engaging it in gear it will die. If I put it in gear and goose it it takes off and goes. The idle speed is about 1200 rpm. It...
  7. B

    Primer for Gelcoat?

    I just repaired my transom and glassed in the top. I am going to spray gel coat over the repair area. My question is do I need to apply primer before the gel coat and if so what is a good primer for this application.
  8. B

    Transom Rebuild

    I am in the process of redoing my transom. I have opted to do a pourable transom. I am planning on going with Arjay. I looked at Seacast and I think it is a good product also. My reasoning for my choice is it looks like the Arjay or Nida bond is more pourable and I will get a more even pour that...
  9. B

    American International Boat

    I recently purchased a 20 foot center console american international boat. They were only made in 1986 and 87. I am trying to find some info on these boats and have had no luck in cyberspace. Anyone out there familiar with them?
  10. B

    Yamaha help

    I have a 200 hp that has a dead cylinder, the problem is the compression on this cylinder is about 110 pounds the rest are about 118 this does not seem enough to make a difference. I have fire there but if I pull the wire while running it makes no difference. I have swapped coils and that is not...
  11. B

    200 hp flywheel

    Does anyone out there know where I can purchase a 1989 200hp flywheel? 6G5-85550-12-00 Any help is apreciated.
  12. B

    Yamaha 200 hp will not turn any rpms

    I have a 1989 200 etx that will only turn a little over 2 grand while in gear.It has turned as high as 3 grand but I can't get it to do it now. It will rev in neutral It would rev till I blew it up that way. Any one have a clue on this?
  13. B

    Yamaha stator help please!!!!

    I have a 1989 200 hp yamaha etx It will run at about a max rpm of 3500. I suspect my stator is bad on the high side. It ohms at 75 on one set of wires and around 700 ohms on the other set. Does anyone out there know for sure what it should be? Any help is greatly apreciated.
Top