Search results

  1. M

    1990 225 etxd need main engine wire harness #6R5-82590-12-00

    Hello,does anyone know where I can get this main engine wire harness assembly,part number 6R5-82590-12-00 .Any help pointing me in the right direction,much appreciated.;)
  2. M

    I can not read anything on this site.....ads

    i am trying to inform myself with expert knowlede,but these ads at the bottom of the page and those on the right side of page make it darn near impossible to see anything!! Does this bother others also?:rolleyes:
  3. M

    1990 225 etxd no tach, and overcharging

    Hello freinds,my motor stared to over charg my batteries and then my tach quit working. I do know if it would be a stator or a something else.also,when it over charged it took out my bilge pump switch. Any thougts on which way to attack this? Thanks.:)
  4. M

    1990 225 yamaha stuck mounting bolts on trim sensor

    Have been soaking these srews for days now with PBS,using hammer and impact driver,not been able to move them at all. Any sercrets that I could try to get these philips head scews out ? Thanks,Ray.:)
  5. M

    two fuel gagues,Yamaha digital and analog,will this work

    I have two gagues on grady white,one is an analog and it works fine,the other is the yamaha fuel management,the analog works fine. My question is weather will both work at same time? Or will one want to over ride the other? I was just tinkering and thinking ,maybe? Thanks.:)
  6. M

    1990 etxd 225 yammie,prime start feul pump...

    Working on my 225 etxd ,prime start system,rebuilt pump,still hard to start cold.Took out themo sensors,cleaned pocket,claned all connection,still hard to start first thing in the morning.Checked plungers by applying voltage,they moved O.K. Is there something I am missing ? Read most all other...
  7. M

    225 ETXD main jets 174 & 164 whitch side...?

    I have rebuilt my carbs and forgot where they were.I see some threads that smaller goes to starboard side ...then other ibfo says large on port side.Very confused by service manual! any replys,thanks!:)I have 164 & 174 size jets.
  8. M

    diaframs on fuel pumps look good but.....

    1990 225 ETXD ,had a good run good rpm and power,then slowly went down hill,till can hardly get above idle. pulled and checked two bottom pumps one port side, they looked good,no tears,rips or dirt,could they still be bad????Preveiously did a carb tear down,soaked in carb cleaner...
  9. M

    proper link setting oil pump,1990 225,v-6

    I have a manual and in different place ,I get conflicting instuctions on how to adjust linkage rod,either with pump at minnium,and another place it says at maxium.just wondering which way to go!!
  10. M

    temp, difference from starboard side (high) to port

    I Just Replaced T-stat And Gaskets On Yamaha 1990 225,and The Starboard Side Runs Higher (180-190*)than Port Side (120's) Any Reason As To Why The Difference? Tahnks!
  11. M

    broken bolt in t-stat 1990 225 yamaha

    Hello,I removed the thermastat,and broke 3 out of four bolts in the process.I was able to heat 2 of them up and the were removed with a great deal of power.The third one would not move ,so I cut it off and drilled it out with a small drill bit,BUT I went to far and went thru the block,I...
  12. M

    1990 extd 225 yamaha electric chocke not working

    Hello,I have a 1990 225 yamaha that I can't seem to get the choke to work. I have inspected the diaframs, and it is o.k., cleaned all the leads to it I could find,still not working. Is there i am missing? I admit I do not have a manual,maybe someone has one on pdf? Anyway, I stuck with no...
  13. M

    Thritle Position Sensor Adjustment

    Helo Friends! I Just Re-built The Cards On 1990 225 Yahmmie.i Had To Remove The Sensor In Order To Take Them Off Of Course,now I Wonder If There Is Certain Postion It Needs To Be In. Any Help? Thanks Mid Fl Cap
Top